Hi all, I am looking at my MPLS service-provider CE router's configuration. On the CE router's wan facing interface (uplink to Service provider's network) there is an ingress policy-map being applied. However, the policy-map has just class-m...
Forum Posts
Dear all experts, when I try to deploy the WAAS services on ISR4451-x router via EZconfig, has below fail log Choose one of the letter from 'a-d' to edit, 'v' to view config script, 's' to apply config [s]: The configuration will be applied and the...
So, I've been tasked with re-designing our internet connections for "automatic failover." To me, it's a daunting project and I came up with two designs. In theory, it easy, but when considering nuances of the network -- VPNs, ppp links, etc. it turns...
Resolved! mroute questions
On R5, I can ping 239.1.1.1 R5(config)#do ping 239.1.1.1 Type escape sequence to abort. Sending 1, 100-byte ICMP Echos to 239.1.1.1, timeout is 2 seconds: Reply to request 0 from 1.1.1.1, 1 ms But the mroute table does not have the route R5#sho...
let us say there is two networks , left wing network and right wing network each with different vlan except vlan4 in common , both connected together through a access port "not a trunk" port of vlan 4 , i have a ip-camera in the left wing network and...
Is it possible to run dual stack IP schemes over an ipsec-protected tunnel interface on IOS? I am able to assign the IPv6 addresses like a normal interface on both ends however when i try to ping across the tunnel with IPv6 there is no response. Here...
Can we configure VRF Lite in Cisco 1921 router ?
Hi everybody, I'm looking for MTBF data for the ASA series firewalls, particularly the ASA-5525-FTD-K9, could anybody assist me with this information? Datasheets preferred but if you have raw numbers, also appreciated. Cheers Tom
Hello all; I have BGP peering between one cisco router and alcatel router. both routers are directly connected.each time that the physical link between the two falls, when comes up the bgp remains in idle state. to solve it, need to reconfigure the...
Out of curiosity, can anyone explain why BGP single customer router, dual-homed ISP configuration would be better than running an IGP or PBR for fail-over?
At home 2811 + 3560. Help set up the IPTV prefix mag250 turns on but the screen is black. On mikrotik via eth1-10.x.x.x on dhcp iptv worksMikrotik: eth1, pppoe-out1-source-nat: masquarade + Igmp proxy Eth1 upstream, bridge-downstream.On cisco2811ip c...
Resolved! why pc's cannot ping each other ?
http://www.mediafire.com/file/urfo6f033vcqire/testo.pkt/file version packet tracer:7.1.1.0138 question:Why cannot pc's ping one another? Thanks in advanced
Resolved! OSPF force route
HiWe have our datacenter in our HQ.From the HQ we got two 100mbit dedicated fiber connections to our branch offices. We have two 2821 routers connected to those two 100mbit connections.Our core switches (layer 3) and the routers to the branch offices...
Hi,I have the setup in the attached image. Basically an SG300 L3 switch which I use as my core switch and 2 switches SG300-28 (for cameras) and SG200-50 (for PCs). They connect to the internet through a Cisco RV042. Both RV042 are in gateway mode. I ...
Hi there! I'm trying to set up some static NAT on a router with a fail over WAN config using route-maps. For dynamic NAT, I have this config part, which works fine: ip nat inside source route-map ISP1 interface GigabitEthernet0/0/0 overloadip nat i...
