I try to install the ASR920-1G-12 license on ASR920-12SZ-IM to active 12x1G, but it says "not supported" during installations. Anybody know if L-ASR920-1G-12 is for this ASR920 platform? I really suspect that is not the case.
I try to install the ASR920-1G-12 license on ASR920-12SZ-IM to active 12x1G, but it says "not supported" during installations. Anybody know if L-ASR920-1G-12 is for this ASR920 platform? I really suspect that is not the case.
Hej guys, I Need some help here because I cannot find any other source in the web. I'm struggling with the very first Basic config for my E1 voice Card on a Cisco 4321 router. It might be I'm missing something but I am not able to see why this is hap...
Explain the seven layers of the OSI model with examples
I was attempting to use my C2801 as the hub in a frame relay setup. However I am only able to go up/up on 2 of the 3 devices needed for this topology. Is this a software limitation? Or am I over looking something here? R2Cisco_2801#sh inventory NAME...
Hello All, I am running the IPSEC over GRE tunnel. And running OSPF routing protocol over tunnel. But the OSPF doesn't come up. Tunnel is up and running. Able to reach the other side of the tunnel successfully. Ping to the destination of the tunnel ...
Dears, ISR4431 is showing 84% of CP DRAM utilization in our NMS. From CLI i see the same ie used memory is 84%. But the committed memory is just 39%. My question is what is committed memory? Do I need to upgrade DRAM? Or need to tshoot? Kindly adv...
Hello, I am trying to implement per tunnel QoS in DMVPN as per the document: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/sec_conn_dmvpn/configuration/15-mt/sec-conn-dmvpn-15-mt-book/sec-conn-dmvpn-per-tunnel-qos.html Based on this document I b...
Haven't had a chance to test this in a lab yet - Reading the OSPF design guide and have a query. If I have 4 routers all using plain text authentication on the same LAN Segment but using two different passwords. Router 1 and 2 have same password, Rou...
I have a question In OSPF Neighbor Adjacency. Can anybody help me to understand. Below is my scenario with 2 Routers and each router configured with 3 loopback interface and two Fast Ethernet interfaces are up.(Router A – loopback networks: 10.1.1.1/...
Has anyone ever be able to trigger default-information originate if the current routing process does not have a default route. I have been able to get something similar to work using a route-map and triggering on a certain address. Basically, I wan...
Hi, I have cisco 1941 wan router. I have Ebgp routing with ISP. I have my own AS number. Problem we are facing is 1 specific website' page is loading blank. I tried to ping that website, it worked perfectly. I tried to trace route that website, it w...
Hello, am setting up an ISP and I want to know if it's possible to use a cisco switchports to bandwidth manage clients, and if it's not possible,any other good solution that can be suggested. thank you
Dear I am new here and beginner in routing and switching. We have two office locating in different cities. We have purchased VPN connection. The ISP gave us two VLAN address pool one for Internet and one for Data Link. I have successfully entered rou...
Hello everyone, I am trying to modify the metric when redistributing connected routes using a route-map. I change the bandwidth value inside the route-map but neighbours still calculate the same value as previous: R1 and R4 are connected to 192.168.1...
You have 5 servers with ip address A,B,C,D and E. These 5 servers are connected to a load balancer. Load balancer is connected to router , ip address of load balancer interface is Y towards router and ip address of router interface pointing towards l...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-14-2025 01:24 AM | ||
05-15-2025 07:28 AM | ||
05-13-2025 03:49 AM | ||
05-12-2025 03:28 PM | ||
05-09-2025 02:25 PM |
User | Count |
---|---|
9 | |
7 | |
3 | |
2 | |
2 |