Routing

 Hello,I would like you to help me with the following issue. I need to connect the following in the router 2911: gigaEthernet 0/1.20 encapsulation dot1q 20 192.168.120.0 255.255.255.0to: gigaEthernet 0/0.90 encapsulation dot1q 90 11.0.12.2 255.255.25...

Hello Friends,A Router 2911 have its Lan interface with dot1q encapsulation, my task was configure its Wan interface with dot1q encapsulation too. The point was that a vlan in Lan SubInterface had to go out through other vlan in Wan SubInterface, the...

Hi Cisco family,I've been working on this config for over month now and its driving me insane. After lot of tweaking I've got this config to work with my BT infinty 2 Internet connection which is a UK based VDSL2. NAT overload works perfectly for all...

Hi.Everyone:I was trying to configure scramble on my cisco2951/k9.It has these licences:ipbase        ipbasek9             Permanent      ipbasek9security      securityk9           Permanent      securityk9uc            None                 None     ...

Is it possible to generate static routes based on an URL?  I've a router with two internet links and would like traffic destined to domain.xyz.com to go via linkA and all other traffic to go via linkB. domain.xyz.com resolves to many different IP whi...

Hi,I'm stuck on a configuration which worked for like 10 minutes, and now not.Config:crypto keyring vrf_management_keyring  pre-shared-key address {DESTINATION_IP} key {KEY}!crypto isakmp policy 5 encr aes 256 authentication pre-share group 5crypto i...

Hi guys. I have 2921 connected to ISP , subinterfaces with appropriate vlans. 2 servers are connected to SVI1 :[ISP]----[2921]-------[SVI1 interface]----[server] I have nat static to that server and ACL allowing only specific public ip to that server...

Dear All,I wanted to configure access list on cisco 2851 router. requesting you please help me.Source :- 11.11.11.11/24Destination :- 10.10.10.10Port :- 7777 Thenks in advance. Abhijit 

Dear All/Akash Agrawal, Actually I am testing failover in eigrp with GNS3  , After configured the Delay (interface gi0/0 , delay 2) still traffic is going via and gi0/0 instead of gi0/1.Can you guide for the above  issue. Best regardsDebadurlav Saran...

I have built a two hub single spoke trial lab. the hubs are then connected to a layer 3 switch. I have configured DMVPN without tunnel protection My hub has a single tunnel with two nrhp entries for the two hubs I am running OSPF for dynamic routing....

Hello,I am not able ping server with packet greater than 1492B. I´m using 3G modem configured as bridge and I used PPPoE to dial connection. It looks like it do not fragment packet. interface FastEthernet4 no ip address ip tcp adjust-mss 1452 duplex ...

Hello, I was wondering we have 2 border routers to 2 different tier 1 providers and seem to use MED for inbound path selection. I was wondering how this works as BGP AS path is well above this so will MED even get looked at? unless there is a tie in ...

Hello,I have stacked together 3 2960x switches as shown in here:http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960xr/hardware/installation/guide/b_c2960xr_hig/b_c2960xr_hig_chapter_010.html#ID173From top: 1st is the master, 2nd un 3rd are...

Replacement model for CISCO 7200 VXR NPE g2 with SAMV2+