Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Resolved! Cisco ISR Wireless Configuration

Hi Everyone, We've just purchased another Cisco ISR, we've had great success with the others which have been deployed however this time we've got one with wireless and it's been a bit of a struggle.   I've been able to assigned the IP address, browse...

Resolved! Design Recommendation

Hello,I'm planning to connect my sites around 100 sites to the HQ site, the provider will connect them using Layer 2 connectivity "wireless" and i will secure the traffic by using site-to-site VPN "the 100 sites will connect to the HQ Router".I will ...

Resolved! COnfiguring an ASA5506X for NAT

Hi I am not sure if this is the correct forum but I need to configure a ASA 5506X to do NAT routing. I think I have successfully configured the internal and external interfaces but so far it is still not working. Any assistance would be appreciated.

Power supply for PoE for Cisco 891FW

Can someone tell me the part number for a PoE power supply for the router Cisco 891FW.Note that it doesn't look like the regular 891 power supplies but it looks like a plastic rectangle with 4 pins.Thank you.

kasper123 by • Level 4
  • 14682 Views
  • 8 replies
  • 0 Helpful votes

OSPF Redistribution - Multiple Areas

Guys, I have the next issue:*I have three routers conected among them, Router 01 has 3 OSPF áreas (0, 10, 30) configured in different processes, in order to connect the other Routers in different áreas, as seen in the diagram attached.Then, there is ...

filter outbound BGP routes

Hello, I'm receiving "internal" routes from one of our BGP peers on a dedicated bgp (neighbor) peer. Our provider who is sending us their internal routes is AS#1234. Our AS is 2345 (changed for a public post) neighbor xxx.xxx.xxx.82 remote-as 1234 ne...

jorg_b by • Level 1
  • 662 Views
  • 1 replies
  • 0 Helpful votes

Router Config for MS Exchange

Hello, I have a problem sending/receiving email through exchange sever outside the office network (Externally) I have already forwarded the following ports to my exchange server 25 - 26 - 80 - 110 - 143 - 443. but it's still wont work.the internet ho...

Qos Bandwidth Limit

Hi,I have 10 Mbps internet connection and have two subnets in my router (172.16.1.0 /24 and 172.16.2.0/24)I want to limit 172.16.1.0/24 subnet to 4 Mbps. This subnet shouldn't pass this bandwidth. How can i do that with qos? 

Route Reflector BGP

I am going to design a  two level Route Reflector architecture in order to get scaling and flexibility for the BGP updates coming for a large number of clients. I am not sure of the basic configuration iBGP and iBGP-RR necessarily for create the core...

Resolved! Disable ISDN connection message on console

Hi! I have a router with two E1 PRI, so I have a many mesage on the console like "%ISDN-6-CONNECT: Interface Serial0/0/0:17 is now connected to" and "%ISDN-6-DISCONNECT: Interface Serial0/0/1:6 disconnected from". This message make me problem with d...

paa by • Level 1
  • 5565 Views
  • 6 replies
  • 0 Helpful votes

Resolved! VSS on 4500X (dual-active when VSL down)

Hi,Have a working VSS with 2 x 4500X's - Testing failover on them, and notice when I disconnect the VSL link, the standby swich reboots - Is this expected behaviour? (dual-active scenario?)sw1-standby>*Mar 24 16:02:28.837: %VSLP-3-VSLP_LMP_FAIL_REASO...

QOS strategy WAN - 7600

hi expert, seeking your great advice on the below scenario:I work in small ISP and we provide internet over DSL and point to point internet as well.We have a cisco SCE in which we use to control customers bandwidth and monitoring. The thing we are fa...

Load more