There are two commands within our companies router that I am unsure of. I need an explanation of these two commands and what they do. Thanks ahead of time.R# AAA Authentication ppp tse localR# AAA Authorization network tse local
There are two commands within our companies router that I am unsure of. I need an explanation of these two commands and what they do. Thanks ahead of time.R# AAA Authentication ppp tse localR# AAA Authorization network tse local
Hi All,I need to understand the values for PCR/SCR to be given on the ATM InterfaceThe topology is Hub end ATM interface ( Bandwidth E3)and Spoke end Frame relay with 1024 bandwidth and 512 CIR.With Frame Relay value can somebody help me to get the P...
We have our own ASN and IP addresses, we have a /24 pool. We want to distribute the same pool on 3 locations is it possible to do the same.
I'm having an issue running ospf point-to-multipoint over a CES cloud. The reason I want to do this is that not every site has the same bandwidth and this way I can use neighbor statements to specify the cost to each neighbor. To make this work I ha...
Hi allI'm been doing some experimenting with multipoint GRE over 3G and I've run into a problem I need some help with. My setup is best described with the attached network drawing. MAR-Router has a fiber Internet connection while the ECK-Router1 only...
Hi, I have a simple lab setup for testing the L2TPv3. Diagram is attached.The router simulated PCs (192.168.10.1 and 192.168.10.2) just can not ping each other. Here below are the comfiguration of the 2 routers. I tried to put in "ip pmtu" under pseu...
Hi All, We are having to terminate a Serial Interface Leased Line onto our Cisco 3825 Router. We have two ways of terminating it: The telecom carrier gives us a G703 interface which we connect straightaway to our 3825 router which requires us to inst...
i have some confusion with IP SLA feature, in this topology i have two links from R1 to R2 and R3, and two default route one primary another one backup with higher AD value (R1-ip route 0.0.0.0 0.0.0.0 2.2.2.2- R1-ip route 0.0.0.0 0.0.0.0 3.3.3.3 10)...
We are investigating to enhance our datacenter availability and would request an AS from our RIR (RIPE) with PI address space. At the moment we have internet access in one facility in Brussels but are expanding to another facility in the Netherlands ...
Hi all, I have a ASR9001 enabled SSH server, it was working fine but when I try to access these messages appear: P/0/RSP0/CPU0:Apr 21 05:31:41 : SSHD_[65747]: %SECURITY-SSHD-3-ERR_GENERAL : Failed to allocate ptyRP/0/RSP0/CPU0:Apr 21 05:31:43 : devc...
On a serial interface(WAN interface), what command would you use to initiate and establish the point-to-point protocol between devices. CCNA help.
Hello SirsIm trying to establish an ipsec vpn connection between my site and an ISP. I have a cisco 1941 router and a cisco firewall on the ISP side. I did the config according to what the ISP have but still the status of connection is DOWN-Negotiati...
Hello SirsIm trying to establish an ipsec vpn connection between my site and an ISP. I have a cisco 1941 router and a cisco firewall on the ISP side. I did the config according to what the ISP have but still the status of connection is DOWN-Negotiati...
we have this old 1841 series router and we change to 1921, i just similarly set the settings same, but only this duplex thing is having problem (i think).we are supposedly to have 20mbps up&download speed using this 1841, and if we use 1921 20down/ ...
In IOS we have the command bgp deterministic-med , in IOS XR what is the command or commands that perform the same operation?Regards.Mario
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-14-2025 01:24 AM | ||
05-12-2025 03:28 PM | ||
05-09-2025 02:25 PM | ||
05-05-2025 11:47 PM | ||
04-22-2025 12:20 PM |
User | Count |
---|---|
9 | |
7 | |
4 | |
4 | |
3 |