Hello All,I'm a beginner in BGP and I'm experiencing an issue. I have two CSR1000v routers, R1 and R2, both connected to a single link provided by my ISP, which is divided into two VLANs, 1040 and 1041. Currently, both BGP sessions are up, and initia...
Hi,I'm trying to install a Cisco Router 2900 by connecting it to my Fastweb Fastgate ISP router.These are the configurations on the 2900 router:interface GigabitEthernet0/0ip address 192.168.100.254 255.255.255.0ip nat insideip virtual-reassembly ind...
Hello everyone,I've read many forum posts over the years which helped me solve many problems. Today, I just can't wrap my head around a solution even though I see lots of information on it.Cisco IOS XE Software, Version 03.16.03.SASR1001-XThe basic ...
If I use the dhcp relay setting in the secondary address setting of SVI, can I assign different addresses to different terminals to receive the data?I have a dhcp relay setup for vlan3 with a secondary address.I would like to have the secondary segme...
I'm trying to enable a NM-ESW-16 on my 2610xm running IOS c2600-i-mz.122-8.T5.bin. During boot the module is seen but that's all. Any suggestions would be appreciated.Smart Init is enabledsmart init is sizing iomemID MEMORY_REQ TYPE00036C 0X000B3B80 ...
hello, i have a sip trunk on a cisco device and am implementing another sip trunk on the same router. So i have had another network subnet has been provisioned and configured on my wan and done required natting on the router. I am able to ping the ne...
Hello, We have just received an C8200-1N-4T router and, unfortunately, we cannot create an ipsec vpn as the crypto commands are not there:hostname(config)#crypto ?RSA-key-pair RSA key pairkey Long term key operationspki Public Key componentsprovision...
I'm looking for reasons to use the same public ASN at two distinct datacenters vs. reasons to use unique ASNs at each. We're bringing a new datacenter online that will have a unique public address space of its own but must also advertise a /24 prefi...
With reference to vulnerability " https://sec.cloudapps.cisco.com/security/center/content/CiscoSecurityAdvisory/cisco-sa-iosxe-webui-privesc-j22SaA4z "what is the difference the commands between "ip http active-session-modules none" and "no ip http"....
Hi. I've studied the idea of loopback interface. Now it's time i actually implement loopback interfaces network wide. Please let me know if this makes sense (I'm just being logical, with no exp here.): We have approximately 100 network devices. Only ...
folksi have an asr 9901 due to be upgraded with the following usage--------------------------------------------------------------------rootfs: 3.8G 3.5G 97% 130Mharddisk: 23G 3.3G 16% 18Glog: 1.9G 163M 9% 1.7Gconfig: 969M 6.6M 1% 896Mdisk0: 3.8G 1.8G...
Hello,I have a ISR4K router connected through Portchannel to a Cisco 3850 switch.Everything is ok so I have put an IP to port-channel on router side and it is pingable.Meanwhile I have created som BVI interfaces working on different Vlans lets say 20...
I am wondering if there is any specific requirement for two routers to form ISIS adjacency over a switched ethernet network ? In other words, when they are not directly connected. I have two ASR9K routers - R1 and R2 - connected directly over a BE in...
I am new to this technology so please be kind. I need assistance in making OSPF work between out Head Office (HO) and the Branch Offices where the ISP is not involved in OSPF routing. We are using OSPF protocol on our entire network and our ISP 1 i...
Hi everyone,Which version of the Catalyst 9300 will be a good replacement choice for the ME3800, we are talking only about routing capabilities?9300 support MPLS, l2vpn, L3vpn ...Thanks,
