Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Dear Experts,We are running 3 ISPs bandwidth via eBGP in our router with our own ASN and IP address.Now our one of the  client has their own IP address and ASN from APNIC .So now what configuration required in my router as PE for our client ASN and I...

                   We have QOS over our MPLS and my provider says that our QOS policies are working fine, but when I run the show policy-map interface command it always shows the EF que with 0 packets and using up 25% of our bandwidth.  We are not ta...

Dan Loring by Level 1
  • 1481 Views
  • 10 replies
  • 0 Helpful votes

Resolved! VLAN across MPLS?

Hi,Apologies for my first post being a question but I've got an urgent problem to solve before Monday morning. I'll try to keep it as simple as possible without missing out any important information.We have moved our servers, routers, firewalls etc t...

Good day.Few week ago we purchase Cisco ASA 5505 as replacement broken Dlink DFL800.I try to configure all setting like it was on DLink, and all work fine with exception of one thing.We have some resource like terminal server, that placed in internal...

Hi all,i have some problem regarding BGP table convergence. There are two router (ASR1K and CRS-3) which have a direct interface and peering with loopback0 adresses.The BGP Peering is established, and prefixes are transfered. However, from ASR1K to C...

Hi Alls,I have some concerns, if we consider QoS, we can configure QoS as following for instance.policy-map **name**  class **name_A**   set dscp default   class **name**   set dscp af20  class **name_B**  queue-limit 8192   service-policy **name_c**...

syjeon by Level 1
  • 317 Views
  • 1 replies
  • 0 Helpful votes

Hi,I came across an error that seems simple but I cant solve the issue. I could'nt pull the startup config from an AP via Cisco works so I connected to it and tryed to do a show startup-configuration. But when I did this, the following error occurred...

HiI have this Ethernet/Token Ring Router and would like to know howto put the interface TokenRing0/0 up?ETHTR#sh versionCisco Internetwork Operating System SoftwareIOS (tm) C2600 Software (C2600-I-M), Version 12.2(5d), RELEASE SOFTWARE (fc1)Copyright...

piotrkrol by Level 1
  • 1361 Views
  • 8 replies
  • 0 Helpful votes

We have a 3600X ME acting CPE with per vrf BGP towards a PE router.Pxe boot for clients on vlan interfaces in the vrf's does not work, while DHCP relay works just fine.We have both the DHCP server and the PXE servers addresses defined as ip-elper add...

jorgensor by Level 1
  • 473 Views
  • 1 replies
  • 0 Helpful votes

Please provide me why my router rebooted?reason is: bus error at PC 0x23B1F92C, address 0x3CWhat does this mean&show ver:Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.2(3)T, RELEASE SOFTWARE (fc1)Technical Support: http://www.c...

Hello,I tried to post this question the other day. I updated the diagram to give a more accurate view of what I wan to accomplish.I want to tunnel a VLAN across the WAN but, I want to connect to the Provider with only one link. I want the VLAN and th...

I have configured Router 1 as followsint gi 0/0.10encapsulation dot1q 10ip add 192.168.10.3standby 10 ip 192.168.10.1standby 10 preemptstandby 10 priority 115and Router 2 asint gi 0/0.10encapsulation dot1q 10ip add 192.168.10.2standby 10 ip 192.168.1...

Hello,I nornally track an interface line protocol when I set up HSRP, but today I noticed a router trackign "sla 1" what is this as there is no reference to it anywhere else in the config:track 1 ip sla 1!interface GigabitEthernet0/1 ip address 172.3...

Unanswered Topics