Egress equipment—core—Access Equipment—Client; now the egress equipment needs to do a cold standby, the equipment is CISCO2921/K9, after the configuration can not access the external network. The situation is as follows:1: The client can ping the WAN...
Forum Posts
what is configuration for adding in CMBD ,SMC , OBS for cisco cisco switch
Resolved! Redistribution with BGP
Hi,I have three routers: R1 --(eigrp)-- R2 --(bgp)-- R3. On R2 I am doing redistribution from EIGRP to BGP. Routing table on R2 looks like this:D 1.1.1.0 [90/130816] via 192.168.0.1, 00:03:11, GigabitEthernet0/0So this is pointing to R1.If I c...
Hi,I will reffer to the following topology: I am trying to identify scenarios in which loop or sub-optimal routing will occur due to different routing protocols and redistribution. I am presuming OSPF of EIGRP under IGP with standard AD.So far, I hav...
Hi all, i have a question about importing routes inside a vrf Right now, in vrf red i'm importing some routes from global routing table and also from vrf blue vrf definition bluerd 1:4102!address-family ipv4route-target export 1:4102exit-address-fami...
I have two devices a firewall and cisco router. Firewall has two IPs public and a point to point /30 network that connects to the router. The router has the /30 and the LAN network. Nat outside is through the /30 interface but when I create a static ...
Resolved! 4321 Out of space for upgrade
I'm trying to upgrade from 16.06.09 to 17.06.05 on my 4321 router Using this command to initiate the upgrade. install add file bootflash:isr4300-universalk9.17.06.05.SPA.bin activate commit The error I'm getting is below. It looks like it is a space ...
Hi. I have a virtual Firepower Management Center and an FTD-1010 on which I've configured a site-to-site VPN for SIP traffic.The tunnel is up and I have a NAT rule configured but, when I perform a packet trace, I'm getting the error:Drop-reason: (ins...
Hello,I'm using a CBS350-48T-4G, and i want to get by snmp the cpu and ram usage on it. but i can't find the correct oid to get those informations. Is it even available?
I'm replacing an old edge device with two Cisco 8300 routers; Dual ISP setup. The 8300 routers were also ordered with 4 port LAN modules. I'm putting together the config before the routers have arrived and want to figure out the down stream config. ...
Hello. Our spoke ISP failed for 4 minutes. Once it returned, our C2921 DMVPN spoke remained in the NHRP state (no production traffic flowed from this spoke to the hub. This was remediated by shutting then no-shutting the spoke tunnel interface (It wa...
Hi guys,I noticed that from last week, I am getting practically every minute or less, a log message like this in ASR log:Jul 26 2023 14:26:46.158: %IOSXE-5-PLATFORM: F0: cpp_cp: QFP:0.1 Thread:199 TS:00084795299536916500 %PUNT_INJECT-5-DROP_PUNT_CAUS...
Resolved! Upgrade to version 7.5.2 on ASR9901
Hello! I recently upgrade an ASR 9901 from version 7.3.2 to version 7.5.2, the version was installed, but when issue the command show install active from admin I do not see the same information, do you know what is the problem. Please help me to figu...
Hi! I have an overlapping problem. Router 1 - on g0/0/0 has ip add 192.168.1.1/16 and on g0/0/1 I want to choose the 192.168.0.1/24 ip add. Here is the overlap. It is possible to keep the /16 subnet mask? What is the solution?
I have a router cisco 4331. Today it rebooted abnormally. I checked the log and got the following results:*Jul 26 02:41:21.290: %IOSXE-0-PLATFORM: R0/0: kernel: mce: [Hardware Error]: CPU 0: Machine Check: 0 Bank 5: d400048000900090*Jul 26 02:41:21.2...
