Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
Hello,Just a quick question :If I have a ROUTER with "Advanced Enterprise Services" and I ONLY need Basic IP Connectivity for Data , will a "Enterprise Base" version go faster ?Sorry for this stipid question , I will attend my CCNA / CCNP Training in...
Hello All ;i have 2 site connected with GRE TUNNELso all ping test are OK but i cannot access to mail server from other site.PING TEST:ping 10.177.80.32 source gigabitEthernet 0/1Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.177....
Hello everybody!I'm trying to configure my network like this:ISP – (VDSL) Router from ISP in bridge mode – Cisco 876 FastEthernet 3 with VLAN4This means the VLAN4 will be my WAN interface. VLAN1, 2 and 3 are connected to the internet through VLAN4.My...
We have three ISP's connected to two routers. ISP1 has a 3gb circuit to our WAN router 1. ISP2 and ISP3 are connected to WAN router 2 (both 1gb).We have BGP to our ISP's; iBGP between the two WAN routers 1/2; and OSPF between the four core devices (t...
I'm seeing very high CPU usage on my new 3560CG-8-PC switch. It's at 61%. Any suggestions how to chase down what's causing it?I'm seeing a lot of rpf-fail drops. What causes them? How to prevent? Supervisor TxQueue Drop Statistics Queue 0: 0 Q...
The host IP 84.204.x.x unable to announce through BGPBGP configuration on Cisco 1841:!interface FastEthernet0.1201 encapsulation dot1Q 1201 ip address 172.18.11.1 255.255.255.252 no ip redirects no ip unreachables no ip proxy-arp crypto map vpn-map s...
Attached is a picture of my network.RedHat Linux Host 1 has a Eth0 with 172.21.0.17/19. Eth1 has 172.21.32.17/19.Since Linux (and all operating systems) can have only a single default gateway, we need to figure out how to have some routes for the Et...
Hello!We have strange problem with our 2911 router.After replacing one router with another with the same IOS 15.2(2) and the same configuration, dynamic NAT stopped working.from sh ip nat translation we cannot see any dynamic translations, only stati...
Hello I am reading Todd Lammle's CCNA study guide....Oer der he says that bandwidth command used under interface config mode has nothing to do with how fast data is transferred...he says that it is only useful for routing protocols like OSPF etc to c...
I have recently made a WAN change from T1 to fiber and my Cisco 2600 series router no longer needs to connect over the Serial T1 card. The Serial connection also provided a few voice channels for the old phone system that are no longer needed. I nee...
Hello all,Does anyone has some info about OPT_E_MAN, I want to run from A to B with two 3750.Thank you.
Hello Hey !! does Fallback sequence in a router i.e. of FLASH , TFTP , ROM IOS happens by deafult or we manually need to configure it using boot system command
HI all, I am getting more memory usage in my Cisco router.show processes memory sorted Processor Pool Total: 145530560 Used: 91726552 Free: 53804008 I/O Pool Total: 38796800 Used: 18544224 Free: 20252576 PID TTY Allocated Freed...
Is there a way to set up an SNMP trap to monitor B/W usage on sub interfaces? Possibly by IP address?
hello,i have a SRP541W which I plug a cable into my Cisco RVS4000 directly.The net on the SRP541W is 172.1.72.1/24 and the RVS4000 is hosting 10.26.101.1/24 - however, whenever connected to the SRP541W via wifi i cant connect to the internet. When co...
