Hey there, I have situation where I need to redistribute static routes into OSPF and apply a cost to prefer one path over another, but I don't really know how admin distance of a static route being redistributed is going to affect OSPF. My situation...
Forum Posts
Peace, when I ssh into it, it displays the following warning: the first key-exchange algorithm supported by the server is deffie-helman-group1-sha1 which is below the configured warning threshold... I tried to regenerate the rsa key with 2048 bits bu...
Dear friends,I am new to VPN IPsec, I have configured this topology in transport mode VPN, (I have done it in tunnel mode)But when I configure in transport mode. I ping from PC1 to PC2 success , but, when capturing packet, as theory, I will see sourc...
Provide me a basic configuration of ASR 1002 router which has the following protocol active1. DHCP2. NAT ( PAT, DNAT, SNAT)3. HSRP4. ACL5. Routing protocols like OSPF and BGPKindly share me the configuration for the above mentioned. Thanks in advance
Hello,we need to implement MPLS Traffic Enginnerring with Fast Rerouting. Which cisco hardware would fit best for that? Due to other considerations ASR-routers are not in scope. br + thx
Resolved! brom> boot on 2960XR switch
We received a new 2960XR switch and on initial boot it goes into brom> mode.CPU rev: BImage passed digital signature verificationBoard rev: 6Testing DataBus...***ERR -- Data bit 3: Expected = 0xfffffff7, Actual = 0xfffffff3, at addr 0x00000000.Going ...
Hi,I try to configure Route-Map to route Traffic to the local Internet Breakout (GigabitEthernet0/0/0).Hardware: ISR-4331iOS-Version: 17.06.05The Client IP "10.9.1.25" should have Internet access via the Route-Map...This do not work.On other old Rout...
Hello Guys,I hope you can help me with this issue, I have this topology with 4 routers running BGP which i want R1's Loopback 1 to have the R2 as an exit point and R1's Loopback 2 to have the R3 as an exit point. With which attribute can i achieve th...
Hi,I have to do a test on a new line, faster, on a Cisco ASR-920-12CZ-A with uses VRRP and has a antiDDoS configuration. What I want to achieve sounds simple to me, place a public IP on the interface, say Gi0/0/3 and set the GW of last resort to this...
So, I'm working on a project that requires Linux host running different programs, and a BMv2 P4 switch in Mininet. I thought a topology as running VM in KMV with my applications running on them and connecting it to BMv2 switch in the Mininet. Is it p...
Resolved! WS-6509E IOS Image
Hi Everybody, I wonder if anybody experience any issues utilizing below IOS in WS-6509-E or VSS switches?Image Files : " s72033-ipservicesk9-mz.151-2.SY4a.bin"We have recently start experiencing random reboots and loosing adjacency issues and appare...
Resolved! Cant get internet access to home lab.
Beginner here. I have a network lab that consists of a Cisco 1841 and a Catalyst 2950. I have a basic configuration that allows everything to communicate with each other. When a device is connected to the switch, I am able to ping every device and ge...
Resolved! Doing EIGRP lab need some help
Hi doing a EIGRP lab need some help with a couple of questions However here is the lab topology, the questions are straight forward first question: R4 is low on memory and should not be queried by EIGRP about routes in the active state. Make sure ...
Resolved! CCNA practise tests - answers unclear
Hello, I'm writing to ask if you could please assist me in understanding how to arrive at these answers. 1/ Maximum hop count is 15, anything more than that is considered unreachable. Here I suppose 192.168.40.1 is 15 hops away then it takes an extra...
I have 7 interfaces 2 in VRF 120, 2 in VRF 140 and 2 in VRF 160 and 1 in global VRF configs: interface TenGigabitEthernet0/1/0ip address 100.100.100.1 255.255.255.0ipv6 address 2012:A2::8/64!interface TenGigabitEthernet0/1/2vrf forwarding 120ip addr...
