Routing

2 isp's from one network

I have a second link being installed this week to a second ISP. Each ISP has tunnels that terminate on there routers for various services. Right now on the 6509 I have a static default route which sends all traffic to ISP one. Once I get the secon...

GRE-VPN routing question

I have a few remote routers connecting to the home office using GRE-VPN and using OSPF for routing.The routing is working properly except for the traffic being sent by the routers directly ( logging to a remote syslog server ).I can ping the remote r...

Resolved! How to upload outputs other than running or startup config to ftp server?

Hi.I know how to upload the running or startup config to an ftp server but I was wondering If there Is a way to upload , lets say , the output of a sh ip int commmand ?

[ITP7613] Can i disable this notice ?

Hi all. I have been using the Cisco 7613 for ITP Sigtran service. And I had upgrade IXH1 to IRE version.(Cisco IOS Software, s72033_rp Software (s72033_rp-ITPK9V-M), Version 12.2(33)IRE2, RELEASE SOFTWARE (fc2)) but i have seen this message at "wr" ...

Resolved! Subnet question (two or more switches connected to eachother)

Hi.I read this somewhere "The limitation of subnetting a network with a router is that all devices on that subnet must be connected to the same switch and that switch must be connected to a port on the router."I thought only routers seperated broadc...

Resolved! ibgp peering

I am trying to establish my ibgp peering. The routers are three ip hops away from each other and we use eigrp for our igp. Nothing I have tried works. Any assistance is appreciated. I am able to ping loopback to loopback without bpg running. My ...

OSPF running b/n DC & branch VSAT links (32 kpbs which is shared)

In one project Im having 1800 hundred branches , 1 DC & 1 DR. The branch connectivty is through VSAT link which is having a bandwidth of 32 kbps (Shared).We are planning to run OSPF b/n DC,DR & branches. By making the branch as a stub, whether...

Resolved! Issues Creating Vlan on ASR 1006

Hello,New to Cisco devices and have had an ASR dropped in my lap.Running ASR1000-RP2 with System image file: asr1000rp2-advipservicesk9.03.03.00.S.151-2.S.binShow Vlans returns: No Virtual LANs configuredRouter(config)#interface vlan ? <1-4095> Vl...

Resolved! Is it Power problem or Link problem .. How to fix ..

We are prime customer of one of service provider and we have connected all our routers's branches through MPLS BGP circuits and we have dedicated network application CA Spectrum to monitor all network devices send alarm via SNMP if location goes down...

Resolved! Problems with Cisco 887 3G functionality

Hi,I have a question about the configuration of the 3G functionality on the cisco 887 router. The 3G connection should be the primary connection, because I don't have a direct internet connection. I make use of a data card of KPN NL. On the internet ...

Resolved! Routing with 3 public IP net on 1800 router

Hi.I don't know much about routers, but lately I've been playing around with router configuration and getting better but I am kind of stuck now.The scenario is this.I have 3 ip net from the ISP:178.249.51.0/255.255.255.248 Gateway 178.249.51.1178.24...

Bandwidth Consumption Tool

Hi,I currently have a 2851 router with 2Mbps point-to-point leased circuit on its serial interface and most of the time its congested.Can anyone tell me if there is a tool for measuring the current consumption that is happening on the link other than...

How to route Internet traffic through MPLS

Hi Everyone,Can someone please help me with the following suitation urgently?I am working for a company based in Sydney Australia, the company recently open an office in London UK, therefore we are going to get leased lined based on MPLS.We were advi...

What platform and IOS version I need to implement IOS SLB

I want to select catalyst 3560G for my network. But IOS SLB need to be implemented in my network. I only know catalyst 6500 series can support this feature and i am not sure whether 3560G can support this feature. what platform and IOS version i need...