Hi,I want to upgrade my IOS on an 871W. In order to do this I need to upgrade the memory. I have found that I need the MEM870-32F (Am I correct?).As in here: http://www.ebay.com/itm/MEM870-32F-32MB-FLASH-MEMORY-CISCO-871-871W-876-877-878-/1606180...
Dear all,I am having a little hard time configuring a PPPoE because the provider is using 2 PVC for the connection. I attached the pic taken from the modem where the service was configured. What I want is to change the modem for the ADSL-WIC and to u...
Hi All,I have some queries which i am little confused here. I used to have a 3560 which was a layer 3 switch and had no issues when used to support a 40 Meg link. However recently I replaced it with a 2960 switch which does not seem to support the 40...
Hello Community,I am setting up a new PIX 6.3 I have a workstation on the inside (192.168.201.10) That workstation can ping the inside interface of the PIX (192.168.201.222) and vise versa.But my workstation cannot get out to the internet using DNS s...
Hi all,I had two routers configured to share the NAT table using SNAT and HSRP.At the standby router I receive this message all the time: Sep 12 11:57:58.939: SNAT: found: (Real IP address, Nat Ip address, 0, 0)And unexpectedly this router had reboot...
I have two sites connected via OSPFSite HQSite DRBoth of these sites are connected via BGP MPLS, as are all branches.Both are advertising certain common networks:HQ is Primary for networks needed by branches, router is configured with OSPF and BGP.DR...
Is it possible to manage users on cisco router/switches - like assigning time slot for usage of certain services. I dont every body on my LAn to use the internet at the same time. How do I achieve this. give some ppl access and deny others access wit...
Hello,Please find attached scenario with configuration filesThis topology is intended for Router Redistribution scenario.Issue #1:Robinson is a router that runs both OSPF and RIP. RIP is running on Robinson's f0/1 interface and OSPF is running on Rob...
I'm trying to set up multicast routing using pim sparse mode across an MPLS line (with BGP routing). I've set up an RP at the main site on the core switch and sening rp announcement (ip pim send-rp-announce). It's working fine at the local site and...
There will be a audit on my customer enterprise network (setup and devices config) by external vendor.Before the audit by external vendor, I need to make sure that everything is fine and no holes as I am managing my customer network. If something fin...
Hi,Kindly i need help in clarifying the attached scenario.As you see, Cairo, Athens and London routers are running RIP. Cairo router is configured for a default route to NYC. I wonder why do i need to redistribute that route to the rest of the RIP ne...
Hello.I need to create a single multicast packet to multiple unicast packets. The reason for this is; we have a unicast-only network between the source and receiver. While exploring the options to achieve this, I came accross AMT (Automatic IP multic...
Hi,LR1 is running EIGRP with CE1 and CE2 and traffic is being load balanced between CE1 & CE2.following two subnets:10.10.10.0/2610.10.10.64/26I want to accomplish following for bidirectional traffic:we want to use CE1 as primary and CE2 as back up r...
it is vsat connectivity..........and we have 40 sites..................& every site having two modem one c band & another is ku band & also one cisco router.......every wan is coming through modems to switch >>>>to router fe ports.............pls s...
I need your help understanding this configuration:I was trying out GRE over IPSEC in my home lab, using the following configuration:R1==>R3==>R2My GRE and IPSEC originate at R1 and terminate on R2, and I verified that the tunnel is up and running on ...
