Hi,For a T1 link to 2 remote sites, our Cisco SE spec'd a 2951 with a HWIC-4T1/E1 at the remote end, and a 3925, also with a HWIC-4T1/E1 at the central site.In considering exactly how these things are going to connect, I've come up with some (probabl...
Hello, we have remote sites using 1841 routers coming back to a 2821 router at headquarters across the WAN. We also have an ASA 5510 at headquarters. What would be the best way to configure an encrypted WAN? Would additional equipment be needed?Sent ...
hi all,i am trying to configure cisco 881g with 3g adapter , when i try to upgrade the adapter it is failed after that i am getting the following error and router keep on restarting . once i remove the adapter from router .it is working fine.13:12:05...
I'm experiencing an issue with OSPF redistribution to BGP. I have 3 sites (as seen in the diagram) - Site A, Site B and a number of remote locations represented as "Site C".I'm attempting to redistribute routes learned from Site A (via EIGRP) throug...
HI ALLI need to know as to what are the different router components and spares that are available with separate part numbers that could be stocked for field level maintenance like flash,ram,etc where can i get this info?
I originally had a single ISP for accessing the internet from my internal network. The Cisco 3845 router has an interface that is connected directly to my ASA for access the the ISP.I have now added a second ISP for access to the internet which is l...
Hi,I'm held up with a requirement and a lot of solutions that I have tried failed to meet the requirement. Hope I can get some solutions hereI have a Edge router with the following connectionsConnection 1 to ISPConnection 2 to remote site 1Connection...
Hi!Looking for advice on what I am missing..I have recently purchased 2911 routers running 15.1 to replicate a system I had implemented using 2811 routers running 12.4 a few years ago. None of my applications and servers have changed, but trying to d...
Hi,I'm trying to configure a cisco 1921 with our new provider and I am having some problems. With the config below I can ping hosts from the router, but not from the private ip's. The info I got from the ISP:wan route: x.x.x.220/30isp ip address: x.x...
We have an aging 2611 router that that we need to replace due to the fact that its 10Mb/s Ethernet ports are limiting our internet connectivity throughput (we have a 20Mb/s circuit).The purpose of the 2611 router was to route traffic from multiple de...
We will shortly be installing a Cisco 3825 router, to be connected to the BTNet service, over fibre.We will be binding many public IP addresses to the router.Is there a way of defining a specific bandwidth limit per IP address, or range?Many thanks
Apart from the ability to participate in BGP, is there any reason you should use a router on an internet edge rather than the SG-300 switch?
HiGuys do y agree with me that MPLS VPN becomes useless in the present of IPSec VPN in order connects branches together?thanks
Hi,I am trying to apply qos on ethernet interfece but i am getting an error. BACKBONE_ROUTER_7609(config)#int g 3/5BACKBONE_ROUTER_7609(config-if)# service-policy output QOSpriority command is not supported in output direction for this interfaceConfi...
I've inherited a IAD2430 router but I don't have the ena passwords nor am I able to do a break and do a password recovery. I'm familiar with the password recovery process and config reg settings but this one has me stumped.The config register is set ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 06-14-2025 01:24 AM | ||
| 05-15-2025 07:28 AM | ||
| 05-13-2025 03:49 AM | ||
| 05-12-2025 03:28 PM | ||
| 05-09-2025 02:25 PM |
| User | Count |
|---|---|
| 10 | |
| 5 | |
| 3 | |
| 3 | |
| 2 |
