Hello Guys,I had installed security license for Cisco 1100 ISR few months ago and now I am getting the below error. I have posted my running configuration and few more outputs. Any help would be much appreciated.Failure reason: Fail to send out Call ...
Forum Posts
I have a configuration consisting of 2 routers meant to be in the same HSRP group, each connected to a L3 switch with routing enabled. The HSRP routers, however, are not communicating with each other because the HSRP packet stops at the L3 switches c...
what are the upgrade solutions for CISCO 3640 Routers.
I'm trying to simulate a PPPoE Server in my office and I can't make it to work. I'm not sure if I am missing something, so I badly need your help. Here's the setup: Cisco ISR4221 router is to be configured as PPPoE Server. One ethernet port (GigabitE...
We are planning to establish a site to site vpn tunnel between our Cisco ASR router and their third party firewall.They have a requirement of back up peer IP. Hence we need to accommodate that IP as well in our config. First we thought of establishin...
HelloI have the following setup in my lab - see configuration further down.The issue is that I do not get response on NAT The idea is to import routes from several VRFs into one common VRF to provide internet connectivity. Doing a debug on the router...
Hi I am trying to configure a cisco ISR router to NAT the destination of an internal IP to a 3rd party providers IP Address. Background: We have hit a bug on our Meraki platform where Meraki Insights will not target a public address which is routed ...
We are going to aggregate two GIG ports of NCS router and connect to the Non -Cisco Layer 03 core switch stack. Please refer to the below mention diagram for more understanding As per above diagram Configuration already made on Cisco NCS 54...
Resolved! Multiple VLAN on router with DHCP
Hey, I am a student and new to Cisco packet tracer.I am trying to enable DHCP on my router 3 for my LAN network. I have 3 VLANs in my LAN network: VLAN 30, VLAN 40, and VLAN 50.They all have to ping each other and the web server 64.100.100.10, the TF...
Hi, anyone can tell me what's wrong with the entry below?(...)RouterB(config-crypto-map)#set transform set mysetERROR: transform set with tag "set" does not exist.(...)So far this is what I have entered onto RouterB:show runcrypto isakmp policy 1 enc...
Resolved! Problem with BGP adjacency
Hello community,I am trying several BGP configurations in a GNS3 lab and i have some issues.BGP adjacencies do not seem to work, as i can not ping several ip address in the network and also they do not exist as BGP entries in the routing tables in so...
Hi Team,I have above mention the scenario. My query is customer end provide 2 ISPs wan links, In case ISP-1 wan link is down. Now the ISP-1 public IP reach globally via ISP-2. Its possible or not, If possible means kindly explain the concept briefly...
Resolved! Static Route for Bridge Group on FP 1120
Hello Cisco's Community. I have next configuration. I am using FP 1120 as router and firewall for my Netwrok. I configured Bridge Group for my interfaces on FP 1120 via Firepower Device Manager. All my clients receive IPs vid DHPC 192.168.1.0/24 I w...
Hello everyone, while configuring RIP in VRF, I encountered a problem where RIP is configured, but it's not showing in the database (completely empty).Here's my configuration:router ripversion 2network 192.168.1.0!address-family ipv4 vrf redredistrib...
Resolved! Double Nat Issue
Hi, Rules:------------1- All routers will be hostnamed, their console/enable security configured (let me know the passwords of course)2- Internet Router and ALL end-devices will acquire IP addresses via DHCP3- PC0, PC1, PC2 and PC3 will use dynamic a...
