Hi, Everybody.could someone tell me something about the command?MBO-RT-02#sh ip ospf de OSPF Router with ID (192.168.167.1) (Process ID 1) Area BACKBONE(0) Intra-area Route List* 192.168.161.0/24, Intra, cost 1, area 0, Connected ...
Hi, Everybody.could someone tell me something about the command?MBO-RT-02#sh ip ospf de OSPF Router with ID (192.168.167.1) (Process ID 1) Area BACKBONE(0) Intra-area Route List* 192.168.161.0/24, Intra, cost 1, area 0, Connected ...
Hello,I'm learning as I go with configuring Cisco routers so please excuse my very basic questions.I have two networks (172.16.0.0 and 172.17.0.0) I need to be able to have the traffic from the 172.16 network access systems on the 172.17 network, bu...
Router is a layer 3 or 4 device if your ans is layer 3 then while applying an extended access list on router interface how specifying port no is aloud as it comes under layer 4 protocols?example:access-list 101 permit tcp any any eq ftpaccess-list 10...
Hi guys,I am in the situation of connecting two buildings with 2x34 Mbps links and I am being requested to encrypt the data traffic , but not teh voice traffic.I have 4x3845s for this task and I have some ideas on how to do it , but if you can g...
Hi,I'v configured the two routers as PPPoE-Server and PPPoE-Client using IOS 12.4T.Now it works out without any problem.Here is the configuration below.********************************************************[PPPoE Server]username client1 password 0 ...
I have been put on a project to deploy the folowing equipment and I have never touched this equipment before. I am responsible for deploying an ASR 1004 with T3, ASR OC3, and 8 3925s with T3 modules. I am working on getting more information about thi...
Hello:I'm a newbie on Routers and Cisco matter. I had been trying to set up a 1841 but I have several problems.I have a network with a 2921 as Gateway and router for a hosted application subnet 10.20.0.X, also I have on the same network a 1841(a) 10....
Dear sir,I have two cisco 4510 E switches now i want to use these two switches in ACTIVE_ACTIVE or ACTIVE-STANDBY mode .Is there any config examples to achive this.srini
Dear All,In Our Network We have a MPLS link as Primary and back-up link as a VSAT.When MPLS Link goes down traffic automatically shift to VSAT, also our requirement is that once the traffic is shifted to VSAT the access-list configured on the router ...
Hi;I'm a little confused about wccp configuration and redirection . I want to integrate with websense cache proxy. On backbone, appliance connected on gig 5/1 for example....Also i want to redirect all http packet on vlan 10.What am i supposed to do...
Dear All, I have following prefix list on my internet router for which need to understand the Prefix list logic. router bgp xxxx (public AS)nei x.x.x.x remote-as 4755neighbor x.x.x.x prefix-list VSNL-ANNOUNCE outnei y.y.y.y remote-as 1236neighbor y....
Hi guys,I was reading through the topic on Ether-Channels, and I'm quite confused, and need your guys guidance.. taken from a book im reading,For example, an EtherChannel consisting of two links bundled together requires a 1-bitindex. If the index i...
Hello everyone,I’m currently configuring a bgp multihoming environment ( two ISP’s - one primary and the other as a backup) I'm advertising my public /24 with my own ASN via BGP to both ISPs. I am only receiving a default route from both of my ISPs ...
I am wondering what my options are for QoS on an ATM DS3 link (NM-1A-T3). I cannot apply a service policy to the ATM interface or the pvc on that interface like I normally do.When I attempt to apply to the VC, it accepts the command but once I exit ...
I have a network with 2 data centers and 100 VPN connected remote sites. All of the remote sites build a VPN tunnel to the primary data center (Site A), though if that site is unavailable, they will build the tunnel to the alternate data center (Sit...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 04:13 PM | ||
08-07-2024 10:40 AM | ||
07-15-2024 05:07 AM | ||
07-13-2024 09:04 AM | ||
07-09-2024 05:41 AM |
User | Count |
---|---|
12 | |
9 | |
8 | |
5 | |
4 |