Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...
I want to configuring Dual ISP Internet Load balancing using 2620 Router. is it possible to configure it?
HiI was testing mutual redistribution between EIGRP and OSPF, under eigrp process without"default-metric" statement, mutual redistribution doesnt work.router eigrp 1 redistribute ospf 4 network 192.168.1.20 0.0.0.3 default-metric 100000 1000 255 1 15...
Hi All,I have a challenge recently to come out with a network design.From the upstream, each customer will need a need to be in a VLAN so that the upstream provider can rate limit the customer per vlan. My network will consist of a DMZ zone (1 firewa...
Hello there,I've got a Cisco 2811 router which I'm installing as the link to our ISP, i.e. it's a border router(outside our firewall and the next hop to the ISP's router).It's a very simple setup - 2 interfaces (1 connected to the Internet and 1 to o...
Hello I have a problem with process of CPU, it proccess is very high SNMP ENGINE 3825#sh process cpu his3825 08:25:55 AM Friday Jan 8 2010 GDL 999999999999999999999999999999...
I would like to know whether Cisco 3750 support QoS-MQC
Hello Guys,I need help in configuring Cisco 3825 cisco router, Customer want to access this router from my SSL VPN means once they connected to SSL VPN they should be abel to do telnet to cisco device , so what routing i need to do in Cisco device?Pl...
Hi, All!Configuration:interface FastEthernet0/0 ip address 172.22.2.63 255.255.255.0 ip nat outside ip virtual-reassembly ! interface FastEthernet0/1 ip address 172.22.4.63 255.255.255.0 ip nat inside ip virtual-reassembly ! ! ip nat insi...
I have a bunch of PCs on the inside of a 3COM layer 3 switch. The switch has the udp forwarding turned on. It then goes to a firewall, which is allowing the DHCP udp packets through, then onto the router which is also the DHCP server. It does not ...
Has anyone switched providers before and run 2 separate MPLS networks as sites were cut over? What are some strategies you may have used to make sure there was still continuity between the 2 networks as you were migrating? How did you assure sites ...
I have a series of routers (Cisco ISR 1811) that has defaulted to an MTU size of 17867. This only happens on tunnel interfaces, and seems to happen for all tunnel interfaces on that series router. The MTU on my 2811 & 2821 all default to MTU 1514 by...
HiI would shortly have Three sites connected with each otherSite_A connected to Site_BSite_A connected to Site_CSite_B connected to Site_CAll are connected via Wimax with Ethernet Interface 10/100 ( 6MB for each connection )Is following OSPF config O...
Hello,I have setup a webpage written in IIS. The webpage allows contractors outside our coporate Network to login and fill in forms that i can process. I have a Cisco router sitting on the edge of our network. I want to secure this Cisco 1800 rout...
Based on the graphic annexWe require that when any machine try entering to www.site1.com (5.5.5.5) will redirect to www.site2.com (4.4.4.4), as we can do this.We Only have administration of all equipment in the network in Building-ARegards.
HiEIGRP supports unequal loadbalancing but applying variance command causes packet drops.I have done as of this urlhttp://www.cisco.com/en/US/tech/tk365/technologies_tech_note09186a008009437d.shtml#topic1Site_A connects to Site_B over GRE Tunnel with...
