Hi all,So I have a campus with two buildings, and each building has their own MPLS link. Also, these buildings have a microwave connection between them.I'm looking for a way to utilize the microwave link to route local traffic between the buildings, ...
Dear All,Please find attached the new setup we are planning to implement in our office.1.2-Internet connections ( ADSL + Leased line both will have fixed ip addressess)We plan to send out the users browsing traffic to ADSL link back up should be via...
Hello all,This is my first post here, and hopefully it's pretty simple. I believe this should be straight forward, but I find myself confused after reading CCIE R&S Exam Cert Guide, 4th ed.On page 476, under "Step 10: Lowest Neighbor ID", the book s...
I have a problem with my CISCO Router, it's 1720 CISCO router series, it was configured for Intranet and i don't know what happens for it, because i can't enter to it's interface using Console port, and i don't arrive to ping to it's adrees IP.I chan...
The title says it all. I have an ASA5505 connected to a residential ISP provider. I configured the WAN port as a DHCP client. The ASA recieved no IP address from the ISP.I then put in a netgear router as my border device and configured the WAN port...
The main question I have here is what kind of cable I need.On one side of the room I have a Cisco 2801 with a T1 DSU/CSU card (WIC?). The other side of the room I have the white T1 box with "CPE1" and "CPE2" ports.What do I need to connect these two...
Hi guys,I would like to set up an ICMP tunnel from the Internet into my private network, which thus requires a static ICMP NAT entry. You can do straightforward PAT for things like SSH (and any other TCP/UDP traffic) into one's network, but as ICMP d...
Hello everybody!!!!I'm desinging a network for 2 eletric substation following some specifications. (see topology.jpg)I need to provide fully hardware redundancy between two eletric substation, provide encryption and VPN.I'm planning to use Two cisco ...
since i have obtained my ccna close to 3 yrs ago, i have finally be given my first real project.... I have to setup from beginning to end a VPN connection to the internet. of hand, i assume i need the following:RouterFirewallthe information given t...
Hi, I have 2 Internet Connection with my client and one cisco router with 2 gis ports.My client has one cheap priced Internet connection and one heavy priced Internet connection.My client has some special demand:- All Traffic should go cheap p...
I have just discovered the 7206 router I have inhereted are only doing FIFO on the serial interfaces. They are attached to full DS3 and max out at about 6MB of traffic daily. We do not do voice or video. I have had some issue with clents complaing o...
I am just learning the 881G router with 3G and am having trouble accessing the AT commands to try and make some modifications to the band that is used. Here is my config.version 12.4 no service pad service timestamps debug datetime msec service time...
Hello,I am finding some conflicting information. Can someone verify for me the maximum site to site VPN throughput for a 2811? Just the IOS VPN, no modules,AIMs etc.Thanks in advance. All replies rated
Cisco 2500Unit 0, memory error, csr0=0x88c3??Message was edited by: Barbara Chamberlain
Hi,We are thinking on how we can make our IPSEC tunnels failover automatically. We have a simple design where the IPSEC endpoint is terminated on a PIX/ASA firewall then the other end is our client. We want to have a mechanism that whenever our clien...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 12-05-2025 03:27 AM | ||
| 11-13-2025 04:57 PM | ||
| 11-09-2025 09:51 PM | ||
| 11-06-2025 06:09 PM | ||
| 10-26-2025 02:24 AM |
| User | Count |
|---|---|
| 4 | |
| 3 | |
| 3 | |
| 2 | |
| 1 |
