Hello guys,i have new question:This is part of my topology:So I have configured static routes on ISP for network 10.30.7.0/24 (PC4+JA1+JA2):ip route 10.30.7.0 255.255.255.0 132.4.4.2ip route 10.30.7.0 255.255.255.0 132.4.4.3On JA1 and JA2 I've config...
Hi,Hi,Access layer is layer 3 , Do I need to make to core and access layer ospf links should be point to point or Broadcast ?What are the pros and cons Thanks
We have multiple locations that are running IOS 15.7(3)M4a on ISR C897VA-K9 Routers. These are getting replaced by ISR1k routers running IOS-XE 17.06.03a. We have an issue with NAT forwardings. This works on the old routers:interface Vlan11descriptio...
Hi Guys,I need to perform a traffic test during a switchover using the ASR903 platform.I would like to know how is the best way to perform the traffic test because when I using ICMP, the traffic is punted to the CPU and during the switchover process ...
Hi everyone，I have a problem about register smart license in ISR4331 with IOS17.3.4.I cant use the command"license samrt register idtoken <token>"，this command is unavailable，so how should I to do？Is there any other ways to complete it？ISR4331#licens...
Hello all,My Cisco Router ASR1001 doesn't store the configuration when I type the write (or copy running-config startup-config). When I reset the device it is configurated defaultly. Do you know if this problem has a solution without sending it to re...
I learned from Cisco CCNA that a directly connected static route specified with an exit-interface has an administrative distance of 0. That seems very promising, because next-hop routes have an AD of 1. I tried to work with these kind of routes in Pa...
Recently, when I log into my switches (SG350X-48), the webpage is super slow to load. it shows "processing data 60%". then sometimes it stops. sometimes it doesn't finish. sometimes it does load but the graphics (links to pictures) are missing. I...
Hello,I have some questions about this routers series.I understand this series is for SD WAN router, i am right ?The router factory configuration is with and vedge IOS.By default all the interfaces are linked to the VPN0, is it possible to use this ...
I'm a total newbie so sorry this I'm using Cisco Packet Tracer I'm simply trying to stop ICMP ping from a PC (192.168.3.4) to the Router 2811 (192.168.4.1) access-list 101 deny icmp 192.168.4.3 0.0.0.0 I get Incomplete access-list 101 deny icmp 1...
Hello guys,I'm working on a project, here's the picture Circle in the middle has MPLS configured, I've configured VRF's and managed to ping 3 sites Split, Makarska and Imotski. Next step I added internet router and configured static routes so each si...
Hi Im from Canada my internet connection is with bell . I have pppoe credentials for internet Bell use 0/35 for internet and 0/36 for video My pppeo work great but i need help for setup my video 0/36 ... this address is received by dhcp from isp ...
Hello,I have a very low speed between two routers using L2TPv3 XCONNECT...One of the router is in PPPoE :interface Dialer1encapsulation pppppp authentication chapip mtu 1492ip tcp adjust-mss 1452How to calculate the correct MTU value to use in the PW...
HelloThanks for your time to help.I am learning EIGRP. May I have your help?In Reliable Transport protocol (RTP), after device send packet to 224.0.0.10, it will wait a time call multicast flow timer. This default is 50, unit is second.If not receive...
In our DC we have ASA 5525 Firewall, while logging into ASDM and under the routes tab i have seen directly connected network 115.110.162.144 255.255.255 so there are 8 IPs starting from 115.110.162.144 to 115.110.162.151, This is Public IP addresses ...
