4w6d: OSPF: Rcv pkt from 10.205.32.2, Vlan1, area 0.0.0.0 : src not on the samenetworkPlz find the error messagesuggest me
4w6d: OSPF: Rcv pkt from 10.205.32.2, Vlan1, area 0.0.0.0 : src not on the samenetworkPlz find the error messagesuggest me
hi, i have 3845 router with two gigabit interface and one serial interface. when i issue sh running command the output for those interfaces is as follows.interface GigabitEthernet0/0 description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$ ip address 2...
Looking for documentation that tells what the maximum number of T1's I can bundle together with MLPPP. I figure that it is somewhat platform specific so if someone can point me to some kind of matrix, that would be good.Searching Cisco's pages has n...
Can you have one router with 2 separate interfaces(2 separate circuits) to provide 2 separate traffic, one for company users and the other for non-company users (Internet Only)? Currently, we have 35 sites connecting to corporate headquarters via ATM...
I want the price for the following ios:c1700-advsecurityk9-mz.124-9.T5.bin I found the price for the CISCO 1700 ADVANCED ENTERPRISE SERVICES Feature Packios on the price list but i can t find the former one Can somebody help ?
Hi all,I have a ISDN issue here, ISDN keep dropping after 20 second exactly, below is the debug captured during the problem:Sep 30 00:41:19.870 GMT: BR0/3/0:1 DDR: disconnecting callSep 30 00:41:19.870 GMT: DDR: Dialer Watch: watch-group = 8Sep 30 00...
Having spot of trouble getting this to work - I have the new ROMMON image loaded OK but the original ROM files loads into memory.
Greetings, i have a BT NTU installed at one of customer sites which presents the circuit on G.703 120ohm, im looking for appropriate baluns to connect between a Cisco 2801 over Ethernet and the NTU itself.Could someone clarify if the products below w...
Not sure if I am in the right section. But we are trying to run HSRP on an interface with a crypto map assigned to it. Thus, I need to get the tunnel to work with the virtual ip address. The trick with this should just be a few commands. I have d...
Hello,I currently am running a 7206 VXR running C7200P-SPSERVICESK9-M), Version 12.4(4)XD8.This router has a gigabit connection to an upstream provider, and on an average day the utilization is about 100Mb in and 85Mb out, roughly 20k-30k pps on each...
Hi, I have the following scenario: site A- OSPF distribution routers -----BGP CE---MPLS cloud------BGP CE----OSPF distribution routers- Site B. BGP is selectively redistributed into OSPF. However, OSPF redistribution into OSPF is NOT allowed. How do ...
Should I be concerned with three of my interfaces on my core router (atm, GB, and Fast Eth.) flushing on the input Queue. The GBit interface has flushed 230,000 times in 7 days, atm a little over 10,000. No errors listed.Thanks
Hi,How does rip v1 deal with fixed lengh subnneted networks,and variable length subnetted works.? Thanks & Regards,jerry
I just need to set-up my 1811 router to connect our LAN to the internet through our ISPs T1 router. It has a static IP address and we have a range of IP address that we may use without NAT. I have established a static IP on the FE0 interface and set...
Hi All,OSPF config on one of the routers..************************************router ospf 100 log-adjacency-changes area 0.0.0.0 range 10.40.11.0 255.255.255.252 area 0.0.0.0 range 10.60.0.0 255.255.0.0 area 0.0.0.0 range 10.100.10.4 255.255.255.252 ...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-06-2025 12:03 AM | ||
02-03-2025 09:24 PM | ||
02-03-2025 07:43 PM | ||
01-13-2025 09:53 AM | ||
01-04-2025 06:17 AM |
User | Count |
---|---|
17 | |
10 | |
8 | |
8 | |
5 |