Hi we have an 876 which connects to our main sites via IPSEC. I want to limit the bandwidth between hosts 10.100.8.201 too 10.100.3.220 at our mainsite. The traffic between the two flows via an IPSEC tunnel 10.100.8.0/24 -> 10.100.3.0/24 I only ha...
One of our customer needs to go for a second ISP for redundancy and load balancing. They r using VSNL IP inside for webserver. Their second ISP is Reliance. They need to use the same IP address when they need to route the packet through Reliance in c...
Router where i try to redistribute from BGP into OSPF -interface Loopback0 ip address 172.22.21.104 255.255.255.255! interface GigabitEthernet0/0 description ### Int to AS65337 ### ip address 9.9.9.2 255.255.255.248 ip ospf network non-broadc...
Hello !I have a Catalyst 2940-8TF switch with MTRJ optical port and I cannot get the optical link up. It wouldn't establish a link with multi-mode optical bridge converter, and it also wouldn't go up if i connect its own tx to its own rx. I have trie...
I have been doing some work using Cisco 7200 series VXR router. I have two questions on traffic shaping. Replies are much appreciated.1. I am using class based traffic shaping using Cisco IOS 12.2. I create a class-map and then a policy-map to shape ...
Which all are the routers can support ISP load balancing.
Please advice!!!Remote 1800 router has L2L VPN back to headquarter. The bandwidth in 1800 router is 1.5 MB. However, sometime the traffic may reach the limitation of bandwidth, and the application will be dropped.Here are the followings we did:1. Che...
I divided a fastethernet (100Mbps) to 10 subinterfaces, each subinterface connect to a unique customer, I applied rate-limit to the subinterfaces. I noticed each customers complained about upload and from the PRTG it looks like each customer is pegge...
How do I invoke controller configuration mode on an 1841 with IOS 12.4?
I dont know if anyone can aid me here, I had a 2811 router which i couldnt remember the password on an so as you do i went into rommon mode and put in the confreg value... but i did the wrong value 0x0214 and now my router just prints jargon.. any id...
Cisco docs state the 3845 can handle (2) NM-1T3/E3 modules. Does anyone know if the router can really support two of these modules?
Pls, i am experiencing unneccessary mail application gulping my bandwith, how do i identify the host doing this on my router
Hello,Trying to setup eBGP with two providers. I would like to use one for primary internet access and the other one to primarily only reach networks part of the second peer. For example only access Comcast users using Comcast peering.NormalSo peer A...
In configuring L2TPv3, I'm getting:Jun 25 10:07:20.077: uid:43 Tnl/Sn 32862/8086 L2TP: Session state change from wait-connect to wait-for-service-selection-icrqJun 25 10:07:20.077: uid:43 Tnl/Sn 32862/8086 L2TP: Started service selection, peer IP add...
Hi Guys Hope someone can help.Our ADSL line connected to our Cisco 877 is suddenly Down/Down. The provider has made me sure that the link was just fine. They tested it with a Layer 3 adsl tester. I notice that the carrier detect (CD) Led in the front...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 12-05-2025 03:27 AM | ||
| 11-13-2025 04:57 PM | ||
| 11-09-2025 09:51 PM | ||
| 11-06-2025 06:09 PM |
| User | Count |
|---|---|
| 3 | |
| 3 | |
| 2 | |
| 2 | |
| 1 |
