Routing

I signed up as a client and I am trying to download the 12.4 ios but it is telling me that I got no right to do that . What shall I do do ?Thanks

Is there any way to access a 2811 router remotley to copy an existing config, or boot to a flash card with an existing config?For example if a branch router fails, can you have someone rack the new router and boot to a flash card with an existing con...

HI all,I have a remote router (R1) with 2 neighbors routers (R2 & R3) using EIGRP. EIGRP chooses R2 as its default route.My questions is, what would be the effect in the default route if i used the "distribute-list" command in R1 due to a bouncing li...

Folks, what is the right design approach for this:Imagine I will deploy 3750-48P switches across a building. Total of 1,300 nodes.What's the best way to calculate the number of switches required:If I do 1,300 nodes / 48 ports = 28 switches. Then you ...

Hi, I have a little difficult, i have 1 2811 with that receive an E1 from one ISP and another E1 from one ISP i want to route by one email services and for another only ftp, www,etc.somebody can suggest a config,

I am currently thinking about using load balancing on two EIGRP enabled links. I don't want to use per packet LB.The problem I have is that I would like to double my throughput for FTP traffic to a specific destination. So I want to use per packet ...

Hi, I have a few VPN's connected to my Cisco Concentrator and ASA. The thing is I have never set the life time on the tunnel on the regional sites configs (877's, 1841's), althought on the ASA and Concentrator I have.What problem's would this create...

Hi,I am using a internet router and it is patted to private IP as 192.168.0.1/24.Now on my L3 3560 switch I created some 10 Vlans.like 192.168.1.1/24,192.168.2.1/24 and so on......I don't want vlans to communicate with each other but just allow all t...

I attach the output of the show_run command of my router that is connected to my ISP. The access to internet is very slow I would like to have the opinion of any of you guys who have more experience and are expert on that subject.Can you suggest to m...

We have offices on a managed MPLS network. Two of the sites have there own Internet connection. One of the sites has a T1 MPLS and T1 Internet connection. The challenge is that on one site, some hosts download 10+Mb files from HQ through the MPLS n...

I have a command under my ospf process as passive-interface Loopback0.I do understand the impact of passive - interfaces , means thy r not going to take part in routing advertisments/mechanisam etc etc.I want to know why the LO interface has been dec...

Hi,Please provide me a solution for this, Is it possible to aggregate dual isp link bandwidth. My customer is planning to take 2 connections from different ISP's. And he would like to aggregate both ISP's bandwidth. Eg:- From each ISP he is getting 2...

This is not reallly a problem, but I am just curious. Please see attachments. This was delivered with a new router with a E3 interface. What is it? What is it good for?

Please help in creating config template for a multicaste routing.From Server: 192.168.11.12Multicaste address:239.0.0.1/5000To seven different Branch offices1.172.16.0.0/242.192.168.201.0/243.192.168.10.0/244.192.168.11.0/245.192.168.12.0/246.192.168...

Hello all,So new to cisco it's not funny! I can cli configure ip and route and flash ios and not a whole lot else. I have seen some configurations for connecting wic-1enet to pppoe session for dsl, but these are all captures of their startup config...