Hello, Cisco community I am looking to configure Cisco 4321 router with Call Manager and pass the SIP traffic to Cisco IP phones. Has anyone done the configuration before? Any help would be much appreciated.
Forum Posts
Hello I was wondering if it would be advisable to manually input my WAN default route as well as it being obtained. I ask because when it is obtained manually via PPPoE it does not show up in "static routes". Curious if I should also manually make ...
Hello -Looking for input on 4331 max IPsec throughput when boost & HSEC license installed We have a case where two locations (both with 4331's) are having internet WAN links updated to 1Gb. The only way to attempt to get the full throughput (general ...
Resolved! Copy HTTP VRFaware
Dear community i would like to use a command like this: copy http://ciscoiosimages.company.local/image123.bin flash:image123.bin vrf LAN I know there are things like: ip ftp source-interface Loopback0 ip tftp source-interface Loopback0 But there isnt...
I migrated configuration from ISR1921 to ISR4221, but find ip load-sharing per-packet command(used in ISR1921) is disable in ISR4221(CEF is enable), only ip load-sharing per-destination is enable by default.know load-sharing per-packet command is not...
Resolved! Bin files for Cisco 7940/7945 phones
Hey team, so I’m pretty new and I just built a home lab, 2x 2811, 2x 2960, 2x 3560, 2x 1841, and an ASA 5505. The issue on having is the Voip phones fully configuring. The phones will boot and it will pull the right default gateway and it will show...
I have planned to configure the snmpv3 from snmpv1 on cisco router cisco ASR1001-X. But I am new on this, so can anyone please provide me the script to configure the snmpv3 in cisco router asap,My solarwind server IP: 10.122.1.1 and It would be grea...
Resolved! Access List Question
I want to separate my network, i have 2 vlans 10.76.0.0 and 172.16.0.0, I don't want them to be able to ping or communicate with each other. I am currently able to ping ex: computer 10.76.2.30 can ping 172.16.32.1, we need to separate them and not al...
Question in topic, I'm looking for 2 intermediate-advanced or lengthy prefix labs. It deosnt matter if it's mixed in with other protocols/coccepts, in fact it's welcome. Please post up Thank You
Hello Seniors, I am a beginner. I am doing a lab of OSPF but my routers interfaces are not getting up. I have run "No shut" on interfaces many times but it's not working. Please find below the packet tracer lab fine. Remember: all routers are in "Are...
I cannot ping from PC1 (IP-10.10.10.5 , DG- 10.10.10.254) to 8.8.8.8 even after configuring HSRP and Vlans also. Ospf routing also is used but I can't seem to find any problem with the routing part. Can anyone please help me?ConfigurationsSwitch A ==...
I an now using Cisco SG220-28 switch.I have created some port based VLANs, and the default VLAN ID is 1.I want to bind specific MAC address from default VLAN to another VLAN.VLAN ID : 1 (Port 1 ~ 12) Port : 1 Mac Address-1 : 12:34:56:78:90:AB (for bi...
Resolved! Help with configuring VOIP
Hello everyoneI have configured everything, OSPF, PAT, DHCP server.. I am ordered to configure voip on another router called VOIP. IP Phones gets ip address (voice ip address 10.172.32.0 255.255.248.0) successfully but somehow, they don't get line n...
Please help me to configure my router for bussiness use this is my old config file.any one can please suggest me the best configuration for cisco 1841 Current configuration : 1388 bytes!version 12.4service timestamps debug datetime msecservice timest...
Test NAT + PBR Deployment Hello. So I have nothing to post as this is a theory and a question on its legitimacy, as in, can it be done this way or what better way. ASA 5508-X w/ 6 Usable Static IP’s x.x.x.182 (ASA WAN) x.x.x.177 x.x.x.178 ...
| User | Count |
|---|---|
| 18 | |
| 11 | |
| 4 | |
| 4 | |
| 3 |
