Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

I have been trying to get ACLS working on VLANs int?s with limited success. I have version 12, advipservices ios.The following command allows me to access 192.168.133.1 on port 25Permit tcp any host 192.168.133.1 eq 25The following command denies me...

Does anyone have hands on experience with the GSR 12016 to 12416 upgrade? I have the 2 CSC and 3SFC cards but don't have a lab router to test it on. Any input is much appreciated.

jkim by Level 1
  • 747 Views
  • 2 replies
  • 0 Helpful votes

I am currently experiencing a problem with multicast.We have 2 separate multicast domains. 1 is statically assigned and the other uses auto-rp.At the border of the 2 domains I am only able to receive multicast traffic from the static side to the aut...

bgibson by Level 1
  • 386 Views
  • 1 replies
  • 0 Helpful votes

How do I add this to a router?interface ATM0/0/0 description ATM Circuit 24.HCGJ.xxxxxx no ip address no scrambling-payload no atm ilmi-keepalive!interface ATM0/0/0.36 point-to-point description Grant Street ip address 10.XXX.XXX.XXX 255.255.255.252...

We have dual 2851's with 12.4(9)T1 on both ends over MPLS the inside sub-interfaces are configured with HSRP groups and track rtr state. We notice upon icmp failover that the rtr state changes to down and the priority decrements to 95 from 105. Below...

jcmattos1 by Level 1
  • 1284 Views
  • 6 replies
  • 0 Helpful votes

Resolved! ASA 5510

Dear All,Now i have problem with ASA5510.i had order ASA5510-k8,so this model not support 3des.my system need to support 3des.How can i upgrate to 3des?Please help me to solve this problem.Best Regards,Join

join_sn09 by Level 1
  • 871 Views
  • 5 replies
  • 0 Helpful votes

hello,i have install a router 7200 with a serial and E1 interfaces.i configure the dialer interface as a backup of serial interface, but whene i shutdown the serial the dialer stay in standby mode.can any one help me pleaz

imane by Level 1
  • 371 Views
  • 2 replies
  • 0 Helpful votes

I have build a GRE tunnel between RouterA and RouterB.There is a OSPF1 router connect to RouterA with ethernet cableanother OSPF2 router connect to RouterBwith ethernet cableall these four router are eanble OSPFhowever OSPF1 router can only form neig...

bamboo by Level 1
  • 768 Views
  • 2 replies
  • 0 Helpful votes

Dear Experts: Would you please help me to understand these QoS parameters, line by line? Our network engineering team leader ordered me to configure this on our switch where our Video Conf. equipment is connected. Here they are:class-map match-all VC...

Hi Experts,I have tried to find the solution but to no avail. Have tried to do a ping from a remote PC to a printer, but seems like pinging with 1500 makes it timed out. Is there any reasons for this?Thanks in advanced.

cindylee27 by Level 1
  • 7003 Views
  • 11 replies
  • 0 Helpful votes

Hi,I want to know if 3845 Router and 4506 Switch with following IOS ver support BGP protocol.Router: Version 12.4, c3845-advipservicesk9-mz.124-12b.binSwitch: Version 12.2, cat4000-i5s-mz.122-25.EWA9.binThanx

raju by Level 1
  • 796 Views
  • 2 replies
  • 0 Helpful votes