Routing

Hi all,i have an 2600 which a want to use for internet access. I'm so far that i can ping everything from the router it's self but behind my lan i'm not able. The only thing i can ping from my lan is the other network in my lan, my lan default gatewa...

Hi,Problem summary: ADSL router fails to bring up BT ADSL connectionWe have set up a 877 ADSL router (UK ADSL POTS) and receive the following debug information following a 'debug atm events'Mar 1 00:24:03.027: DSL: Send ADSL_OPEN command.*Mar 1 00...

Hi,How do you transport vlans across a MPLS network ? MPLS ATom or L2TPv3 ?What about bridge-groups ? Does it have to go through ethernet interfaces ?Any help appreciated.Thanks

Hi there,is anyone using any of Cisco 857/877/1801 in UK on BT ADSL?We've found an in-ability to get ATM to come up/sync with these routers, when using the same configuration we have on Cisco 837/1701 etc, same ADSL line, same RJ11 cable etc.We see:c...

I am seeing some behavior out of OSPF in non_broadcast mode that I would not expect. I haven't identified any neighbors on any interfaces, yet the spokes are forming full adjacencies with the hub. I do have inverse-arp enabled on my frame switch an...

I have read Extended Loopback Tests for T1/56K Lines Document ID: 5708, i m having problem with customer router that have many errors and path code violation but telco had performed BERT test found no error on the lineCustomer router was configured ...

Our office has a DLS line and an 871 router working just fine. we're getting a second DSL connection and want it used primarily for Internet browsing. the original DSL is to be used for VPN connections. Do I need a second router? What is the best s...

Hi AllI am running an all L2 network and need to filter out routes received from one interface to be advertised through another. how can this be achieved ? I am looking at TAGging received routes, but then how can I stop them from being advertised.TI...

I have a requirement to setup a network so that an internal server communicates with outside world through different WAN networks. I have three separate WAN connections terminated on a single Cisco 6500. The internal network also connects to the same...

Hi,We would like to config following:1. setup tunnel in between R1 and R22. R1 is "ip nat inside" and R2 is "ip nat oustde" 3. I would like all users to access "66.221.132.2" this server, it must go to tunnel and through R2, R3 to outside internet to...

Hi,We enable the VPN and NAT on the same route. we would like following:1. 192.168.16.0/24 can NAT to outside internet (using x.x.x.x overload)2. 192.168.16.0/24 can access 192.168.32.0/24 to TW office via VPNdetail please refer the config file. The ...

All,I'm new to working with Cisco routers but enjoy a challenge. I'd appreciate any help that is possible. I've got two vlans on the router, one for the office network and one for a machine control network out in the shop. I have a separate connec...

I haven't been able to access our router using the Security Device manager (SDM) from Cisco. Not sure how to create a new vpn user and add the proper access and password. We already have a vpn group setup. thanks in advance.

Hi,Is this normal behaviour when I have a GRE tunnel between PE and CPE? When I tried to icmp from PE to CPE tunnel address I got the following output in CPE and the ping fails.Jul 4 16:52:57: Tunnel1: adjacency fixup, 10.36.73.1->10.36.85.156, tos=...

We recently added a 2851 router to our network. It connects to a 3750 switch via a MOE circuit. The link is up just fine (interface up, line protocol up), we can ping or telnet to anywhere in our network from the 2851, but we cannot pass any higher...