I have my management interfaces on my switches on a 10. vlan and want to setup secure access to them across my wan. Are there any ways to accomplish this? My switch is a 6509 with sup 720. I have a routable interface on it as well. tks
I have my management interfaces on my switches on a 10. vlan and want to setup secure access to them across my wan. Are there any ways to accomplish this? My switch is a 6509 with sup 720. I have a routable interface on it as well. tks
Hello.I've got a Cisco 1700.Its public address is A.B.C.D (hmmm, secret, isn't it)Its private address is 10.0.0.254Then, behind it, i've got a FTP Server which adress is 10.0.0.2.I need to access FTP from outside, so I need to redirect port 21.Can so...
I recently purchased a 877W for use at the centre of a mixed wired and wireless home LAN.Using the SDM facility I was able to configure the unit with partial success. Wireless is fine and the WAN interface is up; however non of the existing users can...
Hi allI have a Cisco 871W router which I need working in 5 hours max :(So I need help! Router is online, I can access internet etc. I can SSH to the device which is @ 195.49.39.89 which is just fine.BUT, I need to access a server behind the router wh...
Hi Everyone,My question has to do with OSPF and the flooding of LSA's. With redundant links in an area how does OSPF control the flooding of LSA?s to make sure that there are no unnecessary loops of updates? I have heard it sets the TTL field however...
hello,i want to disable http and https access to my router on some interfaces and just enable the same services on the internal ethernet interface. but i found thT HTTPAND HTTPS access to the router are enabled/disabled globaly.how can i solve this p...
Dear All, Does Cisco 7609 router support ISDN PRI configuration with 1 Enhanced FlexWAN controller (8 E1) and PA-MC-8TE1+ installed ?confirm ..aman
HiI have 2600 router and have WIC-2T card.one resonal site is connect s0/0 and internet modem connect so/1 card. For slow of net, I test the serial interface.inside e0/0 is packet 5/sec .then time loop s0/0 is normal but when I give loop s0/1 with on...
Does any one know what this log message could indicate (it must be new in IOS 12.4(12):Invalid decrement of XOT in-use VC count 0It apears right after the following messages:[192.168.0.1,3674/172.16.0.1,1998]: XOT I P/InactiveClear (5) 8 lci 1Cause 0...
HelloI have a Cisco 1811 router and a Cisco 515E PIX and I'm trying to encrypt the communication between them.Now when i connect them to the same network everything is working fine. My case is that i have a router in the middle of those which should ...
Every example I see and what we have deployed is WRED "Random detect dscp-based" on our "class class-default"Why is it, that you wouldnt stick "random-detect" on the other classes you have defined OR would you? Shouldnt RED and the Tail-drop (Weight...
Hi,We need to redirect internet traffic to ISP1 when ISP2 is down or overloaded.When all work fine, LAN1 will go to ISP1 and LAN2 to ISP2We need to allocate bandwidth for LAN1 when both LAN1 and LAN2 go one ISP.How can we do that, how to detect that ...
HiWhat is L3 ether channle?Thanks in advance for reply
Can someone tell me if it is possible to back up/copy my router configs to a usb flash drive so I can load them onto my backup router? I have a 2811 router with 2 usb ports on it,1 and 0.Thanks in advance.
I have certain /30 blocks that I need to be static routed through a particluar SVI on my core router. This router participates in my EIGRP AS on another SVI. When I add the static route for the /30 block...10.194.14.44/30 for instance and then do a s...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
04-30-2025 11:42 AM | ||
04-22-2025 12:20 PM | ||
04-16-2025 08:28 AM | ||
04-15-2025 06:30 AM | ||
04-11-2025 05:02 AM |
User | Count |
---|---|
6 | |
5 | |
2 | |
2 | |
1 |