Hi,As annouce the cisco 1750 router already EOL. Does the new Cisco 4 ports Fast Ethernet Switch WIC and Single Port Ethernet WAN Interface Card compatible with Cisco 1750 router?Can it be integrate into that router?thanks
Hi,As annouce the cisco 1750 router already EOL. Does the new Cisco 4 ports Fast Ethernet Switch WIC and Single Port Ethernet WAN Interface Card compatible with Cisco 1750 router?Can it be integrate into that router?thanks
Good mooring,Please,i need a simple configuration example with vrf between 2 routers acts as PE and P.Regards.
Hi,We have a Site to Site VPN setup that comes into use when the primary links to our London site go down. Yesterday we lost the primary links and along with it alot of connectivity.We use floating static routes to tell our router to pass traffic to...
Hi Previously I use a Cisco 831 router and just got the Cisco 871W and Cisco 2960 to implement QoS to control the network traffic. On Cisco 831 where we could 'match protocol http mime {mime type}' in class-map, however on 871 they do not have the ...
I am setting up a 2801 with QoS for VoIP. The following QoS config works fine on 1721s, but we are having issues with outbound voice on the 2801s with this policy. The IOS is 12.4(9T)ipbase.policy-map QoS-Policy class VoIP-RTP priority 512 class cla...
Has anyone had to enable OSPF routing on a PIX 525 v6.3? should I expect problems CPU % others issues? the other option is put a 2811 router in front of the FW and in to our core network, so are the ISR routers secured enough to be used instead to b...
I have a lab setup for learning BGP. I'm trying to understand why I cannot ping the loopback interface of router c from router b. Three routers.Router A - Lo0:10.252.1.1/32S0:192.168.27.1/30S1:192.168.27.5/30S2:192.168.27.9/30router bgp 65000 no sync...
Hello,We are bonding 3 T's with MLPPP on a 2811 router. I am looking for any information on MLPPP configuration. From my understating we aren't doing anything but bonding those 3 T's. Can anyone point me to some documentation or possible provide m...
I have a 2811 router. Two WAN interfaces are UP in that router. When I check in "sh ip route" output, then I get the below mentioned output. Router#sh ip routeDefault gateway is not setHost Gateway Last Use Total Uses Inte...
Hi.which the command to measure the temperature of router 2801?
Hi, I have noticed that it is common for my GRE tunnels to bounce a few times after a power cycle with two log messages that are repeated several times:%DUAL-5-NBRCHANGE: IP-EIGRP(0) 1: Neighbor X.X.X.X (Tunnel1) is down: holding time expired%DUAL-5...
Hi,we have big performance problems with the NPE-G2 and PA-FE-TX. The throughput over the PA is only 1 mbps. Any ideas ?The software is SP Services 12.4(11)TCarsten
We have a Router connected to a TACLANE encryption device (router-to-taclane remote taclane-to-router). The TACLANEs setup VPN tunnels between each end point. Does this meant that using Router GRE tunnels prior to TACLANE VPN not a possible design...
I have serveral AS5350 routers serving PRIs from serveral Telcos. Recently I was tasked to bring up several PRIs from a CLEC. The CLEC breaks out a DS3, which is handed off to two other carriers before we get it. The last carrier breaks it out int...
I have to configure my 870 router for bridged ADSL. I managed to configure it for pure bridging, but I would like to use IRB. This implies that I should improve my knowledge of IOS. I looked at this article:http://www.cisco.com/en/US/tech/tk175/tk15/...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-10-2024 12:41 AM | ||
10-05-2024 05:56 AM | ||
10-04-2024 06:22 AM | ||
09-23-2024 06:56 PM | ||
08-07-2024 10:40 AM |
User | Count |
---|---|
11 | |
11 | |
7 | |
6 | |
6 |