Any thoughts or request for info? I found a link with a error code table but it doesn't seem to align with the error code I am getting. https://www.cisco.com/c/en/us/support/docs/ip/trivial-file-transfer-protocol-tftp/13705-15.html TFTP%Error openin...
Forum Posts
I followed guides and help on Cisco Forums as well as sites such as (https://support.voipdetective.com/support/solutions/articles/48000618409-enabling-cdrs-and-cmrs-in-cisco-call-manager). All steps have been followed regarding unchecking the "CDR On...
Resolved! deactivate nim card on c4331
hi, can i stop those out of service modules from appearing ..alarming due traps sent to my monitoring system? blah#show platfoChassis type: ISR4331/K9Slot Type State Insert time (ago)--------- ------------------- --------------------- -------------...
Here's just a simple question that I don't have an answer to.Suppose that we have the following topology switch A - Router B - switch Call 4 ports connecting to each other are access VLAN 5If switch A sends out an arp request on VLAN 5 towards Router...
Hi All, Site A <BGP protocol> Backup Site B We did the scenario of Stacked Site A whole switches 9300 are down and backup site of Stacked Switch 9300 did not pick up on it because the subnet of switch gateway vlan IP (Vlan 221) on Site A which is no...
I have a 2901 router (c2900 -universalk9-mz.SPA.157-3.M5.bin) that is simply connected to a cable modem the router has a static IP assigned .It works for a while then stops passing traffic after a while .It will restart with a no shut command or if i...
Cannot ping to ISP 64.100.0.1 from PC1 I can ping to 64.100.0.2 R1 router directly connected to ISP My ip route 0.0.0.0 0.0.0.0 64.100.0.1 does not seem to do the trick Any ideas? R1 Configuration (output abridged)R1(config)#ip ro...
I have a ISR4331 router with Boost license of 300mbps.. i have Router on a stick/inter vlan routing on the router. below are my interfaces.. GigabitEthernet0/0/0Gi0/0/0.3Gi0/0/0.4Gi0/0/0.5GigabitEthernet0/0/1Gi0/0/1.555Gi0/0/1.666Gi0/0/1.777GigabitEt...
Greetings, So I've a topology which includes several LAN topologies. The current setup have all static routing and configured Ip address in all devices. The problem that I'm encountering is that the end-device circled in black couldn't send PDU to th...
Resolved! DMZ and Production Server design
Hi Everyone, I've just come across a DMZ design by someone else for the first time so I will need some advice/opinion on this. From my knowledge, I'd separate the DMZ network and production servers onto 2 different network, 2 different physical inter...
Resolved! cant ping 8.8.8.8
Hi everyone, I have setup this topology in EVE-NG.R1 is connected the management cloud, which connect my topology to my physical home network. R1 configurations: Linux-PC IPv4 settings: What should I do to let my Linux-PC ping 8.8.8.8 or any public ...
Resolved! Unable to ping routers G0/0/1 Interface
Hello Everyone.I am trying to build a small network and based on my skills i tried setting up 2 routers, but seems like they can not ping each others G0/0/1. Below is my configurations. RB:show run | begin interface interface GigabitEthernet0/0/0 i...
Hi! Cisco IRS 1100 Series, C1111-4PLTE I was pushed to create config for small company. Outside ip: 10.100.100.182 Inside ip: 10.10.10.2 There is command: ip nat inside source static tcp 10.10.10.2 587 10.100.100.182 587 vrf OVERISP extendable ...
I'm testing vPC in GNS3 but the LACP port channel on switch keeps getting suspended. I keep seeing this on Switch however vPC is up on the remote Nexus switches:*Apr 10 20:08:18.412: %EC-5-L3DONTBNDL2: Gi0/0 suspended: LACP currently not enabled on...
Hello All,I have 01 ISR 4431 router in that 2 ISP link (MPLS-BGP) terminated and 01 LAN interface is configured with HSRP.Now, client required router level redundancy. In which we have to terminate on link on one ISR router and other link in second I...
