Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Hi,Can you give me some knowledge about Intelligent routers.Are there any routers currently in the world wide web which can do some additional tasks.for example :listening to a particular port for special type of packets and reacting differently depe...

Does anyone know why I might receive AAL5 length violation errors but not oversize SDU errors: MTU 4470 bytes, BW 3840 Kbit, DLY 20000 usec, reliability 255/255, txload 68/255, rxload 42/255 Encapsulation ATM 23035716 packets input, 10690163751...

I tried to upgrade IOS to c2600-js-mz.122-26b.bin on my 2610 router, and I added 2 commands:boot system flash c2600-js-mz.122-26b.binboot system flash: c2600-js-mz.122-26b.binand start to upgrade. But the router kept restarting after upgrading, then ...

Hi all:I have 3 three years old 2610 router,which include 1 ethernet port and 2 wic slot.Now I want to add another ethernet port,but can't find any moudule can fit my needs.Anybody has a idear?Thank you in advanded.

sip_james by Level 1
  • 556 Views
  • 3 replies
  • 0 Helpful votes

hi. i have earlier post asking what router and switch to get. with the help, i got 1841 router with one t1 interface card and catalyst 500 for switch. i'm having problem with installing. right now i have one t1 point to point and one cable intern...

choisam77 by Level 1
  • 551 Views
  • 2 replies
  • 0 Helpful votes

Folks, We have EIGRP running in our network. One of our remote offices uses internet connection from the head quarters. We have a PIX firewall and to the best my understanding it does not support Eigrp.So we are pointing our MSFCs at the core sw...

Hi,My network has two ADSL 512Kbps lines and I am doing per-destination load balancing with CEF enabled.I am getting a few link utilization graphs from MRTG server for both the dialer interfaces and ATM physical interfaces. I would like to know if I...

yvasanthk by Level 1
  • 510 Views
  • 1 replies
  • 0 Helpful votes

On a 2621 router with an internal dsu/csu iI am getting this with a sh interfaces serial 0/0:Serial0/0 is up, line protocol is up Hardware is PQUICC with Fractional T1 CSU/DSU MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, t...

ryocca by Level 1
  • 1332 Views
  • 1 replies
  • 0 Helpful votes

I have 2 Cisco 3550's (3550A & 3550B) seperated by a Cisco 2600. 3550A is connected to our Voice lab on VLAN54 in it's own subnet. I am trying to configure bridging on the 2600 to allow me to put ports on 3550B in VLAN54 and be in the same subnet as ...

us10610 by Level 4
  • 391 Views
  • 1 replies
  • 0 Helpful votes

Here is what we would like to do:We would like to put our 506e right behind our router and infront of the rest of our network. Everything is on the same subnet. We would like to use the 506e for VPN and firewall.Is all this a pipe dream?Thanks.

What is the maximum numbers of VPN tunnels that can be defined on a PIX 515E firewall. I don't need the max number of sessions. I need the max # of VPN tunnels that can be defined in the config file.Thanks

vpresher by Level 1
  • 798 Views
  • 2 replies
  • 0 Helpful votes

i want to do load-ballance between the two atm , and the problem is that any time the all transmit pass throuh one atm ,and it's don't do a load-ballance between the two atm.what is my problem?no service padservice timestamps debug datetime msecserv...

If I have 2 equal cost routes, but one is a Metric Type 1 and the other is a Metric Type 2, which one will be preferred?Also if the Type 1 has a forwarding addres and the Type 2 has 0.0.0.0 as the forwarding address which one will be preferred.Many T...

tsalt by Level 1
  • 366 Views
  • 1 replies
  • 0 Helpful votes