I need a help in configuring nat.My net 172.29.4.0/24 should be patted with a global ip 82.x.x.x, but when i try to reach 192.168.0.0/24 over a ipsec VPN, i need to avoid nat totally.I readed something about route-map.Some help please.Thx.
Hello, i am trying to enable isis on my 4500s. When i configure the isis net it does not show in the running config nor is it saved when the router reloads. However it is active until the reload occurs as clns neighbors form. Is this normal?
Hi,I have a C7204 router, working in sgbp group, serving L2TP tunnels for the braodband. The router is crashing, with the following message on the console.TLB (Store) Exception ***Access Address = 0x84PC = 0xbfc052c0, Cause = 0x800c, Status Reg = 0x3...
I have a 3745 router with 2 2Mbps leased line from differents ISP. i have also some VPN connection on each leased line.when i use 2 default static routes with 2 ISP, all VPN connection become down.
Are hardware modules in the 3660 hot swappable? I have an NM-2W with a wic-1t module to be inserted into a 3660 hardware platform and I just want to confirm this model supports hot-swapping.
Hi All,One basic question to you about bandwidth utilization measurement of ATM links !!We are using the MRTG to measure bandwidth Utilization of all our WAN links, and in all cases we could see the utilization growing upto 100% in peak time except o...
Hello,I am a IOS beginner and I recently purchased a 2514 from EBAY. I would like to deploy it on my Windows-based home network. Would simply like to route between 2 network segments but don't know how. Can anyone help me with the configuration? ...
Has anyone ever configured VWIC MFT 1-Port E1, 2811 router. The router is currently installed in Mexico, and we are trying to connect to PSTN in Tijuan, MX. There is not much from Telco. They won't even tell us whether it is an E1(PRI) or E1(CAS),...
Hi alltwo routers are connected via two serial port R1=====R2i configured both the serial port s0 and s1 with ip add 192.168.1.1/24 on R1 and ip add 192.168.1.2/24 on R2. It was working and load balancing was also working.can somebody guess what is h...
dir Sir:i have two routers , and i enable the bgp using ibgp (internal) and the both are connected by ethernet, and have the following configuration:Router 1:router bgp XXX no synchronization bgp log-neighbor-changes neighbor 192.168.209.1 remote-as ...
Hi Sir,Attached is output of BGP table that I came across in a book. There's one prefix in the table with two paths.I notice that the LOCAL_PREF attribute is not shown for routes learned via eBGP. My understanding of LOCAL_PREF is that it is configur...
Hello All. I have two sites, each with a 3640 running version 12.1. I have three T1's between the two sites. I want to load balance the three T's. I was looking at Multilink PPP, but our lines are bouncing when using PPP for encapsulation. We...
I did a debug eigrp neighbors, and I got the message "EIGRP: Packet from ourselves ignored" every 5 seconds. I found I could get rid of it by making the loopback interface passive. So is this just cosmetic, or is it considered good practice to make...
I 'm configuraing pix firewall 515, version 6.3i want rip to advertise the direct connected route to its neighbor.How can perform it ?Any suggest will be appreciate.Best regards.
Hello,i am searching for an particular ios command to set an serial interface to down if the router recognize that the line is flapping or that the line has errors (e.g crc).Is there a tracking command for the line or something else ?Thanks for all r...
