Hey, Is there a way to add expiry to a user account on Cisco 800 Router Series?
Forum Posts
Resolved! Setting higher OSPF priority cost?
Hi, I think this will be an easy one for most of you but i just want to make sure.I have a router in the field that has two links back to our main network. Both links have an ip vlan with ospf on them.One of them is having problems and causing packet...
Hello, So i am trying to config router RIP v2 with this subnet IP: 129.208.63.1 but when i do it with command "#network 129.208.63.1" In Routing -> RIP i can see just Network Address 129.208.0.0 (!) The same happens when I do 129.208.48.0 and so o...
Hi there, For our monitoring and automation research I'm newbie in this solution. I followed the cisco information for the configuration. However I think to achieve access the topolopgy is as next:- vrf with public access using a VLAN and Loopback. T...
Hello, dear users, have a little problem with my lab. The task is to create three networks using three switches 2960-24TT with next ip addresses:192.168.3.0/255.255.255.0 (/24);10.0.1.0/255.0.0.0 (/8);172.17.1.0/ 255.255.0.0 (16)192.168.4.0/255.255.2...
Resolved! VRF default route leak
Hi, In our core router we have 20 VRFs and it also receives full bgp tables from two ISPs for the Internet.So far, we have provided Internet to only one VRF, but we are planning to make Internet available to all VRFs in the future.We do not have enou...
Hi,HSRP running on nexus 9k sh ip ospf neighbors There are multiple VLAN , out of 10 VLAN one VLAN shows EXCHANGE/DR and the other side EXSTART /BDR what could be the issue switch2 172.16.10.110 1 EXCHANGE/DR 20w0d 192.168.8.3 Vlan10...
Good afternoon.I have configured BGP with BFD on my cisco ISR4451.During a tshoot session I have checked the "show bfd neighbors detail" and i found the following output: router#sho bfd neighbors det*** output omitted ***Registered protocols: BGP CEF...
Resolved! vrf Mgmt-vrf (managent) issue
Hi all, -I'm trying to configure a interface loopback under default vrf Mgmt-vrf and the follow log appears: %IOSXE_MGMTVRF-3-INTF_ATTACH_FAIL: Management VRF attach to mgmt loopback failed%LINEPROTO-5-UPDOWN: Line protocol on Interface Loopback10...
hi team, how much bandwith do i need to configure HSRP or VRRP between tow routers thanks
Resolved! Limit bandwidth using p2p xconnect
Hi everyone, Im traying to limit the bandwidht using pseudo wire configuration between two cisco IOS XR 9904 (6.4.2 version). The problem is that Im using a "bundle-Ether" to do this. Could someone give me a hand please? The config that I have is......
My cisco2921 router always boots into ROMMON. I can manually boot it by using the IOS in flash0.What's the problem? what can I do?Thanks in advance!The following is the output of console:System Bootstrap, Version 15.0(1r)M16, RELEASE SOFTWARE (fc1)Te...
Resolved! MPLS Traceroute not showing all hops
Hello, I work with an MPLS service provider, we have this weird this with our Cisco routers, when the client does a traceroute from their Site-A to Site-B and also do the opposite, they get difference results, always missing 2 hops. The client thinks...
Hi Everyone,Can anyone please explain while advertising routes to BGP peer why we create a static route pointing towards null 0 when it won't make any value. I mean after adverting the network to our BGP peer, our router/L3 switch will consider those...
I have done all the necessary configuration on My firewall (access list, nat, default route) but I still cant ping to the other network (out side)
| User | Count |
|---|---|
| 3 | |
| 3 | |
| 2 | |
| 2 | |
| 2 |
