Hi, I have a Cisco ASA 5525 running ASA version 9.3(3)9. In the config I have around 17 Inside subinterfaces with Security Level 50, configured on the same port-channel.Internet is working as it should with the Outside interface set to Security Level...
Hello. I'm not into Cisco at all, but fate has decided that I ought to make some changes in my Cisco 881 router. I need to forward several ports to allow users to connect thru VPN tunnel to WinServer2019 which is behind NAT.My public IP is x.x.171.5,...
Hello im confused trying to create a ACL... I need to block traffic since 192.168.40.0/26 to 192.168.80.0/26 and i need to allow traffic from 192.168.80.0/26 to 192.168.40/26but i don't undertand how can i do it, i tried put a ACL in R2 deny traffic ...
Hi all,I have configured a bgpon router CE:router bgp 800bgp router-id 8.8.8.8address-family ipv4 vrf db-bkuredistribute ospf 2 match internalneighbor 83.0.0.3 remote-as 100neighbor 83.0.0.3 activate"neighbor 83.0.0.3 update-source loopback2""neighbo...
still all icmp traffic block outside of the network access-list 101 deny icmp any any echoaccess-list 101 permit ip any anyinterface FastEthernet0/0ip address 192.168.2.92 255.255.255.0ip access-group 101 in still icmp block on wan interface any any ...
HI all,i need to know is there any command we can issue to see how powerful processor chip my router has?
why we use vrf and tell me for how many purpose it use..please tell me the full condition?thanx ja
Hello everybody, I hope you are all doing well.I'm writting today because I need some help in BGP routing, here is the context.I have 2 CISCO 9300 series and I will connect to a provider vía L3 using a dedicated VRF with BGP inside, I have total cont...
Hi all!I was studying the knowledge about OSPF, and there is a paragraph in RFC2328 about type 5 LSA that I didn't understand：'AS-external-LSAs are the only type of LSAs that are flooded throughout the entire Autonomous System; all other types ofLSA...
Need help to understand route between Vlan and Vrf configured vlan We have 2 L3 vlan created on core switch. Int vlan 26Ip add 10.18.71.1Ip ospf 100 area 0 Int vlan 413Ip vrf forwarding RedIp add 163.122.136.94Exit Ip vrf redRd 6453:RedRoute target...
Hello all, Trying to make sure I understand the different MTU settings on a Tunnel interface. Say I have the following output from a show interface Tunnel1 MTU 17916 bytesTunnel transport MTU 1476 bytes And say I have the following config set in sh...
Hello community im having an issue with port forwarding i have a local device at SITE1 local lan 10.0.0.30 9100 im forwarding to dialer1 global port 9100 which is working, i can see the port alive when i scan the wan ip address with a port scanner.ip...
Hello all, I'm facing a route flapping issue, on a setup with redistribution.We have OSPF running in the HQEIGRP running on the WAN, on top of a DMVPN setupWe have an other OSPF instance running at the partner side. As we have 2 points of redistri...
Hi im testing the QinQ feature between 2 ASR920 routers - i want traffic flow between 2 bridge domains and i want to use double tag for testing purpose. is it possible on the ASR920 to use a S-TAG lets say vlan 100 and then have the inner C-tag untag...
VIm trying on my desk to configure two Cisco C1117-4PM connected to eachother using the vdsl interface on a standard telephone cable. Running 16.12.03 image.RoutingI've read the configuration information regaring setup of these controller, but all ...
