Dear Sir, On IOS platform, I can use "kron" to execute "show run | redirct tftp" to backup the router configuraiton automatically. May I have you help to check how to backup the rotuer configuraiton automatically on NCS IOS-XR platform ?
Forum Posts
Resolved! MPLS VPN v4
i am trying to ping from Customer A to Customer B via vpnv4, but it not went success,Lab story:-First i configured OSPF inside the provider network, and make connectivity from one PE to other PE.Second configured MPLS on all internal router inside pr...
I have configure a NTP server using a DNS name on a IOS router.But when I boot the device and the DNS server is not available on config load, the IP address doesn't get resolved and never asks the NTP server.Is there any way to force the router to lo...
I have an ASA 5505 and I need to port forward multiple outisde ports to an inside host. I usually do a port forward to a single port with the following, as an example for external access to cameras via cli: object network CAM_8000host x.x.x.200 (IP o...
I have a router connected to switch 1 – vlan 2, vlan 3 : switch 2 – vlan 3, vlan 2. Vlan 2 and 3 are their own separate subnet, and have computers communicating within their own vlans. Currently VLan 2 computers can not communicate with Vlan 3 How c...
Hello, I currently have an PTP going from my satellite office to my main office. All traffic goes through this connection. I have a new connection coming in in which I would like to route internet traffic out separately. Currently, traffic all go...
Unfortunately I don’t have a router configuration to show everyone because that’s what I would like the kind people on this site to send to me one. I have a dhcp scope on my Windows 2019 server and its going to give the following computers these addr...
Hello everyone , I have a problem on my packet tracer, in fact I would like to add 2 IP route on my router but I have "%invalid input detected" I don't now why.. If you have a solution enjoy Gautier
Hi everybody, I have some questions about license issue. I thought only there was only one image to any device, and then you select the correct license depending on what you want to use. Now, I would like to upgrade my IOS, and when I check web I can...
At one of our sites we have our own router Cisco 1941 router connected to an ISP router also Cisco as happens I can remote onto our 1941 router using its wan IP no issues there But when I connect through our management loop back address I am getting ...
I have a n9k switch where I have couple of vrf's like management,default,107,108 . Traffic is getting routed via management.I want to make 107 vrf accessible to outside network.I have very limited commands in management so can't leak routes.
Greetings and thank you for your time, To summarize/simplify my issue, we have two ISP to which we need to conditionally advertise our public subnet to ISP 1 but not the ISP 2, unless ISP 1 is down. We don't want to use AS prepend to ISP 2, we simpl...
Hi master. I have router ASR9K with single ISP (ISP-A) using BGP routing. now, my company need to add new ISP (ISP-B) on Router. The ISP-B carry single ip neigbor (peering) with dual AS, for example AS-300 for Internasional (IIX) and AS-400 for (...
Hello, ASR 9006 High cpu usage on RSP1.Сan someone explain to me what the problem is?Thank you!sh logRP/0/RSP1/CPU0:Mar 6 12:16:23.394 : wdsysmon[446]: Process hd_drv pid 49186 prio 21 using 50 percent is the top user of CPURP/0/RSP1/CPU0:Mar 6 12:16...
This is how I do it on ASAobject network L2L_NAT_OVERLOAD_IP host 10.200.255.1object network L2L_NAT_DST subnet 172.1.1.0 255.255.255.0nat (INSIDE, OUTSIDE) source dynamic LAN_INTERNAL L2L_NAT_OVERLOAD_IP destination static L2L_NAT_DST L2L_NAT_DST th...
