I HAVE NEW ASA5516-FTD-K9 and I need to add in my topology my current equipment's that i have now as below :I have cisco catalyst 2960 x 24 gige poe 370w 4x1g sfp lan base qty. is 2 switches /Cisco CISCO2911/K9 ( CISCO 2911 VOICE BUNDLE PVD 3-16 UC...
Forum Posts
Hello, I just found this command ip arp gratuitous none I understand the ip arp gratuitous make update to the ARP table immediately when connect on port in the Router or switch. Is this right ?So if we used none here what this will mean ? and this...
Resolved! BGP & Static route
We have a single ISP. We connect to that ISP via a 1G fibre ethernet connection into a private MPLS network. This uses BGP routing for the fibre ethernet.We are thinking of utilising a backup connection (using VRRP) to the same ISP into the same MPLS...
I have a CISCO1921 with IOS 15.3(3)M5 and its behaviour differs from what I would expect from the config.Overview:10.4.10.0/23 local network for clients (no overload, web access via proxy, see below)10.4.12.0/24 local network for guests10.4.14.0/24 l...
Hello, I've got a project where the customer has over 70 sites that pretty much all use draytek vigor routers and these all connect to our network for l3vpn on the mpls. However, they want to plug in a 4g dongle to each of these drayteks for failover...
Resolved! Nexus - BGP --> EIGRP route-map problem
Hello expertsI have facing a problem on the redistribution backgroundin my company mainly EIGRP, but recently we have 1 site setup VXLAN, so some of the Eigrp router they need to exchange the route will becomes EIGRP---> BGP ---> EIGRP but seems th...
Resolved! BGP aggregate address?
I'm using the above topology in GNS3 and I'm trying to use the aggregate address command on the edge routers to advertise all of the 192.168.0.0 networks but I'm running into something I don't understand. If I do it this wayEdge1#sh run | s bgp ro...
Hi, Can anyone please advise : Whats the difference between using VSS and HSRP. What are the pros and cons of both. How can we know "when to use VSS" and "when to use HSRP"
Does the Cisco SF350 class of router have an external HTTP-based (or other) interface that can be used to extract port and other information? In my application, I would have a number of such routers providing ethernet packet delivery service to all m...
hi i am trying to work on my project on gns3 I do everything right but i can't see the OSPF neighbors relationship between my router and Layer 3 switch Topology and configuration as follows Router 1 connects to L3S on interface Eth1/0L3S connects to...
Hi, I am having an issue with a Cisco ASA 5506X and ospf routing and running ASA 9.14.The Cisco ASA is connected to edge router and learning default route from the edge router. The adjacency is established between the router and the ASA in full and r...
Hello, I have an ASA 5506-X on which I have configured 3 different VPN tunnels to distincts peers (also 5506-X or similar). All tunnels are coming up alright, configurations are fine.I'm trying to replace my ASA with a RV160 and configure the same VP...
Dear All, How to initiate a TCP connection to the BGP peer? Is 'listen at port 179 to open it up' is one of it? Please help. Thank you!
Dear All,I hope you guys are well.I have configured IP to MAC and binding on Cisco 3845 Series Router. It is working fine.But the thing is that I do not want anyone to get an IP address from the same DHCP server? If there MAC address is not binded w...
Dear All, I have recently bought the 900 ISR router and installed CCP express cisco-config-pro-exp-admin-k9-3_5_3-en when I use IE11 , I got display issue, see attachedand it is not usable, cant select the button properly if I use chrome, firefox, op...
