Hi, So I just got a new ISR4331 router for connection with my ISP, the router is meant to have 4GB default RAM size. I intend to use the router to receive full BGP table from my ISP and I believe that I should be able to do this seamlessly as theoret...
Dears, It is confusing to understand what is the default throughput of ISR 1000 series router, i have been through different links and on every link the throughput differs , i hope somebody can help me to understand the default throughput.Also i woul...
Hi, simple scenario. PC want to get to server. ASA check by IP SLA availability route to Server A and to Server B. Is there any option how to translate NAT IP on ASA to local IP of server according availability? (Server A a Server B are on different...
Hi All, I am having a problem with OSPF neighbors stuck in the state of INIT. I am currently running a point to multipoint network. The core of the network has a Cisco 6509 installed and at each remote site either a cisco 3750x or a cisco C356...
Dear i am planning to have a LTE 5G technology on ISR routers 4000 or 1000 series, can anybody suggest me that do isr routers support 5G, becz i see the last support for LTE advanced Pro which is cat18, do we have anything 5G supported currently or o...
I have a lab set up in my garage, like this:A router(B) connected to another router (A), this router (A) connected to two core switches, both connected to a server switch. At the end, a raspberry pi connected to F1/0/3 on ServerA. All configs attach...
Dear Community, i have an c1111Router.Which is the latest ios to use without smart net?i got a license file, IP Base.but cannot install because smart net is enabled.I read somewhere, only ios up to ? can use without smart net.please advice
Hello all, been a couple of days in total since I started to investigate Multicast Routing on the 9300 CISCO Catalyst (Gibraltar V.16.12.02) Have been looking around on forums and seems like my application is a little bit too specific, not a common s...
Greetings network pros,I'm a bit of a rookie and I am sure I am missing a simple command/configuration.I have Cisco 3925 router. Gi0/0 is from the modem (DHCP IP). Gi0/1 is configured to hand out 172.16.1.X IPs. Gi0/2 is configured to hand out 172...
Hi! I want to configure a pair of ISR 4351 for a redundancy. I read in documentation, that stateful redundancy supported for zbfw and Nat functions. I also want to have stateful redundancy for my ipsec site to site vpns. But I read it's only support...
We recently set up a second ISP connection to help offload some traffic to and increase our bandwidth on the first connection. Our network basically goes like this > ISP> ASA> web filter> Core switch. The second ISP connection is set up the same way ...
Hi AllI have a few questions around BGP - I have always read that the first path that gets installed in BGP will be the one that is always used even if a newer better path comes in, however I read in another document that the best path will always ov...
i have a problem on a dhcp relay. how can pc with vlans 34 37 42 and 46 can get IP on dhcp server? vlans 3 5 9 and 14 can get IP on DHCP server because it is connected directly on L3 switch but PC not he right with vlans 34 37.42 and 46 cannot get ...
hello , i have asr1006 and i used it for PPPOE server for user For example 500 users is connected to router via PPPOE and they have all of them downloading fileand i config when user connected he get Policy-mapPolicy Map user Class class-default p...
Let me explain my topology. The HOME-RTR has three sub-interfaces: g0/0.10-30 with 10.10.10.1, 10.10.20.1, and 10.10.30.1 as the gateways. It is connected to HOME-SW via the trunked port Fa0/24. The HOME-DC Server is part of VLAN 10 and is connected ...
