Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Labels

Forum Posts

Hi all.I have Cisco RV260W with 3 vlans configured:Vlan 1 : 192.168.10.0 (used for team)Vlan 2: 192.168.20.0 (used for public wifi (investor comming visiting us etc..., no need to acces internal network) )Vlan 3: 192.168.30.0 (used for external partn...

emaid by Level 1
  • 864 Views
  • 2 replies
  • 0 Helpful votes

Can we use the Mgmt port (int GigabitEthernet 0) SNMP without removing the existing Interface.??  Router(config)# snmp-server view myview mib-2 includedRouter(config)# snmp-server trap link ietfRouter(config)# snmp-server trap-source GigabitEthernet0...

Hello team.Please tell me where can I find information about IPSec performance for router CGR1120/K9 with licenses "SL-CGR1K-IPB-K9" + "SL-CGR1K-SEC-K9". I can't find anywhere information at the vendor's site.Many thanks for your help.

Hello, I have a Cisco 2900 router and run the DHCP server on it.  What I would like to do is, except for 'handing out' DNS and GW etc, also  'hand out' the address for the NTP server (which is the router itself). browsing around I found something lik...

roncro by Level 3
  • 2682 Views
  • 4 replies
  • 0 Helpful votes

How can I clear this on our aci leaf.Type-5 AS External Link StatesLink ID ADV Router Age Seq# Checksum Tag10.0.30.220 172.25.0.227 1862 0x80005ba4 0x6475 348972602810.0.95.180 172.25.0.226 515 0x80005581 0x22d2 348972602810.0.98.16 172.25.0.226 515 ...

Hi Guys, I have an issue, we have deployed the VM with dual nic and enabled the DMZ mode. As we are using 2 NIC, Inside and outside. This setup is working fine. However, I have a challenge here, on the outside interface my network is 192.168.113.X, a...

Hi all, I have a Cisco 1921 router (15.3(3)M8a) with EHWIC-4G-LTE-G card. Everything is working, but I'd like to lock the 4G band that the modem is using. Two bands are currently available on this location: band 3 (1800 MHz) and band 20 (800 MHz). Th...

tgts by Level 1
  • 901 Views
  • 0 replies
  • 0 Helpful votes

I'm preparing myself for new CCNP exam and working on a lab where I have 5 routers running BGP, R1 advertises network 192.168.20.0 and the Loopback1 is 192.168.20.1. Route is advertised and installed in the routing table but I cannot ping loopback in...

elpablito by Level 1
  • 2339 Views
  • 3 replies
  • 0 Helpful votes

HiIf we have multiple licenses on Cisco ISR4451-K9 like Appx license, PERF license, HSEC license and we mentioned these during device order with cisco. so1) Will it be installed and activated by Cisco and send to the site ? else2) Are we gonna have 3...

Sri1024 by Level 1
  • 326 Views
  • 0 replies
  • 0 Helpful votes

Hi ,  3845 citi router fan got failed and i got the below error msgs. Please suggest to fix it Jul 28 09:30:55 IST: %FAN-3-FAN_FAILED: Fan 3 had a rotation error reported.Jul 28 09:31:15 IST: %FAN-3-FAN_FAILED: Fan 1 had a rotation error reported.Jul...