In which type of situations would you use Unicast and Multicast? Is there one or the other you should always be using? Also, I was told when using hosted voice and you have like 10 VOIP phones only on the one switch that you should be using Multicast...
Forum Posts
Hello, I have the DHCP server running on the router, it ands out IP addresses, but for the wrong subnet.I am trying to use only static bindings in pools, with an "origin file" like: *time* Apr 20 2020 5:11 PM*version* 3!IP address Type Hardware addre...
Resolved! Policy based routing or not
Hello for everybody. We are going to install new ASA in one of the offices - current scheme in attach. But before installing, i would like to make sure that all the new settings are working. For these purposes, i plan to create a test vlan 100 (192.1...
e had configured a site to obtain dhcp address from the hub site about 2 months ago. we have had no reported issues the weeks immediately thereafter. However about a month later we have been experiencing voice latency issues. I'm just wondering can ...
Hi all, is there a way to reserve CPU cycles on a Cisco router for management/control operations? We run into issues time and again where a smaller ISR (1941 etc.) would get overwhelmed with a sudden influx of IPSec traffic over the VPN tunnels due...
Question with BGP load balancing. Unless I missed something, is it possible to use BGP load balancing for redudnant links to single ISP? I have read > https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13762-40.html and the d...
Hello everyone! I am currently learning OSPF and i have a hard time identifying what went wrong in my configuration. I use packet tracer to simulate my Frame Relay (1 hub & 2 spokes) with the following condition. 1. Hub will be able to ping Spoke 1...
Resolved! Packet tracer scenario help
So I’m pretty new to packet Tracer and I’ve been given the scenario which I need to complete and I need your help because I don’t really know how to do this. The router Central, ISP cluster, and the Web server are completely configured. You must crea...
Resolved! Redistribute static route issue
I cannot understand why, while static route can be redistributed to EIGRP over the network, I cannot ping from directly connected interface from R1 to R5, just from Loopback. R1 output:R1#sh ip route ... Gateway of last resort is 0.0.0.0 to network 0...
Resolved! how to config netflow
Cisco IOS Software, c7600s3223_rp Software (c7600s3223_rp-IPSERVICESK9-M), Version 12.2(33)SRB5.how to config netflow,monitor the atm port.
So I upgraded my cisco 9300 to fuji from everest however I did not realize that fuji requires smart licensing. Is it possible for me to downgrade to everest from fuji? Will it revert back to traditional licensing or will it still require the smart ...
Hi, I'm currently working on a solution for a client wherein we are running a FHRP to a customer to handoff private network traffic. Our edge site routers are advertising the customer hosts back into our private network via iBGP. The host routing a...
I installed two Cisco ISR4331routers in my SOHO model and they are both set up with a GLC-GE-100FX fiber interface add on module for gigabitEthernet port 0/0/2. One only has two ports being used right now, the GLC and a standard RJ-45 port and the fi...
Hi Everyone, I have 2 x ISPs which connected to my edge router R3 with BGP. My public subnet 209.24.12.0/24 is advertised to both ISPs. I'm currently receiving default route from both ISPs and partial internet routes. I have BGP neighbor setup and c...
Hi,I have 3 C819G-4G-NA-K9 that have LTE backup when the primary DSL link fail.As of now the setup is active-standby on the LTE through DMVPN tunnels.Both Tunnels (DSL and LTE) are up but the traffic goes through the DSL first.The routing protocol u...
