Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hello everyone, I have set up 3 networks which are connected trough multiple routers. All of them are connected trough the RIP protocol.The connection works fine, I can get from one network to the other ones.But when I create an extended access-list ...

luxgil by Level 1
  • 1887 Views
  • 5 replies
  • 0 Helpful votes

Hi What if I configured Distribute-list, route-map, filter-list, prefix-list all together what is the preference order of BGP? for Ex:neighbor 2.2.2.2 prefix-list XXXX outneighbor 2.2.2.2 distribute-list 101 outneighbor 2.2.2.2 route-map XXXX  outnei...

Hi Team,  Any one could guide me how to restore from this boot process  Current image running: Boot ROM0 Last reset cause: LocalSoftCisco ISR4431/K9 platform with 4194304 Kbytes of main memory media drive bootflash: not presentboot: error executing "...

UniWAQ by Level 1
  • 5556 Views
  • 6 replies
  • 0 Helpful votes

hello guys a few days ago I'm setting up a WLC 5508 with a sw 3750I could do the entire network but I can't connect it to my isp routerI can not find the solution and it is driving me crazy I can see the ap I can connect to them everything works perf...

Hola!  Tengo una topología que verán en la siguiente imagen, tengo diferentes numero de vlans tal como 12,30,40,50,60,70, configuré una nativa 99 para el enlace troncal, entonces solo se dan ping las computadoras que están dentro del rango de rede de...

Adalkis by Spotlight
  • 962 Views
  • 3 replies
  • 0 Helpful votes

We have several remote sites connecting back to a central site for Internet access (connected via AT&T's ASE). Recently, we enabled multicast routing everywhere to support a particular application on our newly installed Cisco phones. The application ...

We are currenty trying to test a setup for GRE tunnels using DMVPN on a pair of 7200 routers using version 12.3(24a) acting as aggregators, a Catalyst 4948E L3 switch and an ISR 900 4G router. When our tunnel is configured with DMVPN commands like :i...

dimitri0s by Level 1
  • 1151 Views
  • 5 replies
  • 0 Helpful votes

hola, como descargar software de administración (vManage) y actualización para el cisco ISR4331.  llevo horas tratando de descargarlo, y si intento descargar las actualizaciones me pide un contrato nose de que. porque todo es tan engorroso :/  ayuda ...

Hello!I'm trying to config remote backup acces from Cisco 4221 to switch 2960L using router's combo aux/con port. I connected these devices with rollover cable. The router doesn't have physical aux port, but it has combo aux/console interface. Config...

Resolved! Issue with ISR4221

Hello, having IP phones connectivity issue with ISR 4221 Router, internet working fine, below is the configuration: Router(config)#do sCurrent configuration : 1752 bytes!! Last configuration change at 04:37:06 UTC Wed Jan 22 2020!version 16.5service ...

Cisco7777 by Level 1
  • 2567 Views
  • 9 replies
  • 0 Helpful votes

Resolved! C2960 bootup

i will try to give just the basic info. I have a c2960 switch, files were deleted from it. I copied (c2960c405ex-universalk9-mz.152-2.E9.bin) from another switch to a usb. I can get the switch to boot normal from the usb and have copied it to flash b...

What is the default maximum-age of a Type 1 OSPF LSA? A router with ID 222.1.6.1 is on my multiaccess segment. I was logged on to 222.1.7.1 with log-neighbor-changes enabled; I powered 222.1.6.1 down and watched the adjacency vanish; but the 222.1....