Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Don't miss this Cisco Catalyst 8000 offer

 
Labels

Forum Posts

Finding accurate answers to your questions and issues is always gratifying, but what if these answers are shared globally across different languages? The Cisco Community team has been working on a proof of concept (PoC) to take Accepted Solutions in...

translator.png Asolution.png htlm-source.png insertcode(1).png
Kelli Glass by Community Manager
  • 10217 Views
  • 7 replies
  • 16 Helpful votes

We recently moved our HR dept to it's own vlan and since doing that I am unable to get RDP to work to the HR computers from the VPN. I was hoping someone could help. I don't fully understand the nat rule order, if I move the HR dept to the bottom of ...

jkay18041 by Level 3
  • 1421 Views
  • 11 replies
  • 0 Helpful votes

Resolved! NAT issue

I've got an ASA 5516 that I'm having issues with NAT on. Currently it seems to work except for when I try to access a public IP on my subnet. The outside interface has a public IP that is part of a /26. From the inside interface if I try to ping, acc...

maniac79 by Level 1
  • 484 Views
  • 1 replies
  • 0 Helpful votes

Hello, Here is my topology: I have dynamic NAT on ffw.lim.rt01.VLAN 10's gateway is 10.0.1.1 on ffw.lim.rt01's g0/1.10. VLAN 20's gateway is 10.0.1.17 on ffw.lim.rt01's g0/1.20.Each VPCS can ping each other.VPCS can ping 72.145.30.1 thanks to NAT. I ...

Screenshot 2019-05-11 at 22.17.04.png
angristan by Level 1
  • 2339 Views
  • 7 replies
  • 0 Helpful votes

We have two BGP neione is IBGP other is EBGP to ISP below is one route show ip bgp 1.32.225.100BGP routing table entry for 1.32.225.0/24, version 2263349Paths: (2 available, best #2, table default)Advertised to update-groups:3Refresh Epoch 16327 1299...

mahesh18 by Level 6
  • 556 Views
  • 2 replies
  • 0 Helpful votes

Hi Does anyone know if the older 3900 routers require any type of license? Or does it not have any software license restrictions?  The newer ISR4331 router do require a license sometimes for data transfers larger than 100 mbps. Thanks.  

hmc2500 by Level 1
  • 697 Views
  • 2 replies
  • 0 Helpful votes

I am trying to understand the DNS lookup order on the router. Let's say I have the following config:ip host aaa.com 1.1.1.1ip name-server 8.8.8.8when I try to ping:#ping aaa.comTranslating "aaa.com"...domain server (8.8.8.8)Type escape sequence to ab...

pingduck by Level 1
  • 4248 Views
  • 7 replies
  • 0 Helpful votes

Hello, I am having issue with Remote access VPN users which will not able to ping to inside network because of a dynamic PAT statement which translating that subnet to internet. However, once I removed that NAT statement VPN users will be able to rea...

Back in 2017, I started on an embedded router project, but shortly after, it was put on indefinite hold.  Recently however, it has started up again and I needed to run some performance tests on a DMVPN (using iperf3).  We had received an evaluation l...

jbize by Level 1
  • 1203 Views
  • 4 replies
  • 0 Helpful votes

We have ASR Routers with 3 BGP neighbour's which are 3 different ISP's.We are learning routes from all of them From ISP 1 we are learning full Internet Routing table.IF we lose physical link to ISP 1 will our Router learn all the routes from ISP 2 an...

mahesh18 by Level 6
  • 1791 Views
  • 21 replies
  • 0 Helpful votes

We have ASR router and it has few ISP connections. Say it is learning full routing table from ISP 1It is learning 48000 routes through ISP 2It is learning 7000 routes through ISP 3 Questions1>If traffic goes to specific website via ISP 3 will it alwa...

mahesh18 by Level 6
  • 823 Views
  • 6 replies
  • 0 Helpful votes

Hello, I have a ASR 1001-X. Have 3 ISP's which I want to terminate onto it.Have 3 VLANs on my 6509E switch. Vlan 10,20 and 30.Vlan 10 uses ISP1, Vlan20 uses ISP2 and vlan 30 uses ISP3.How do I do the above on ASR.Also, if ISP1 fails how does vlan10 a...

Rajan R by Level 1
  • 916 Views
  • 3 replies
  • 0 Helpful votes