Hello, we have 3 branches connected via leased line to a ISR 4331, the branch router also have a backup-connection via dsl to a backup-router (also ISR 4331), the branch-router have 2 IPSEC-Tunnels: one to the primary router via leased line, one to t...
Hello, I'm trying to setup a pppoe-client config on an ASR1001 running asr1001-universalk9.03.02.01.S.151-1.S1.bin.When I want to add the "pppoe-client dial-pool-number 1" under the ethernet interface, the command is not available. Could this be link...
For this discussion, imagine the topology: - Running Sparse-Mode on all the links- R5 is the BSR & RP for all groups 224.0.0.0/4 in this multicast domain- R4 is just another PIM-SM router which we will use to source multicast traffic later.- IGMP ac...
I've a customer who wants to peer some of our network devices so that in case of a loss of our authoritative NTP sources, they will remain synchronized with each other. These devices also act as NTP servers to every device downstream from them. In es...
I am new to routing. I made 4 different networks in packet tracer and they work individually but i don't know how to connect them so that I can ping PCs on different networks. right. How do I do this!?! Eigrp? Static? Forgive my ignorance and any hel...
I have two N9Ks connected to each other with OSPF running between them using unnumbered loopbacks. If I go to either switch and do a show ip route x.x.x.x (to it's peer) I get two possible candidate routes. Everything works fine and I can ping my ne...
Dear ExpertsI am stuck with traffic moving from access switch to multiple places. Please guide me that how to achieve the tasks that are given below and also mentioned in attached packet tracer topology.Tasks1:1) VLAN 16 is fast moving traffic and sh...
Dear all i have Cisco 4451 router along with ucse modules,1. I have installed Fortigate FW on VM as i configured the HA but unfortunately its nor working need your support .2. iam try to ping from the diff PC with in diff vlan ( i asaign the diff...
Hi,We have cisco 5505 with device manager version 6.4I am trying to run nat (inside,outside) cli commands and its not taking in. Do we have incompatibility with those commands on this version? Just trying to configure l2tp vpn for win 10 users but ci...
I have found a few places that discuss this issue:GigabitEthernet0/1 is up, line protocol is up Hardware is MV96340 Ethernet, address is 0024.979c.29a1 (bia 0024.979c.29a1) Description: 20Mbps to AT&T AVPN MPLS service AT&T Ethernet ckt id - MMEC97...
Hi,Is There Any Scenario To Use The "Permanent" Parameter At The End Of a Static Route Command ip route .... permanent
Hi community. I'm having a problem with a Cisco500-to-Cisco500 family I had configured as site-to-site. Everything was working until we changed ISP in one of the sites. The old ISP was giving me a static public IP which was working like a charm. On t...
Hi,Is There a Way To Specify Different Bandwidth Size Of Sub-Interfaces, For Example:If I Had A G0/0 Interface, And I Created 3 Sub-Interfaces G0/0.1, G0/0.2, & G0/0.3. Is There a Way That I Can Manage The Bandwidth So That G0/0.1 = 600Mbps, G0/0.2 &...
Yesterday I was invited for a job interview from a company for a junior network administrator position. I am currently looking for my first job as I am a fresh graduate. The guy who interviewed me asked me this question, this is how it went:Guy: Can ...
I want to distribute only one static route to OSPF.ip route 10.55.254.0 255.255.255.192 10.80.60.5 My config:ip prefix-list DMZ201 seq 10 permit 10.55.254.0/26route-map DMZ201-TO-OSPF permit 10 match ip address prefix DMZ201 router ospf 200redistribu...
