Hello I am new with Cisco Configuration. we have 2 C2960XR-48FPS-I stack and we need to have Wifi, voip, server (DHCP) and internet and I need to have 8 different vlans for WAPS, Server, Access, Voice, etc, and all those vlans need to comunicate in b...
I have a single 3945 which has 2 x Fibre providers terminating onto it (say Gi0/1 and Gi0/2). There are multiple VLAN's and subnets on the router, one of which is solely dedicated to Gi0/2. Gi0/2 lives in a VRF with its own DHCP/NAT/Crypto maps (and ...
Hi community team, I have Applied Create a route-map to forward HTTP/HTTPS traffic to Proxy but still, there is some traffic not belong to HTTP/HTTPS is actually been forwarded to the Proxy server, would you please advise me with the solution? In ...
Hi Network ,File transfer got aborted on 10MB circuit and WAN circuit is connected to Cisco 2951 Trying to transfer 14GB windows image from one site to another site but its always get failed when file transfer reaches 1GB. Brief : 10 MB WAN circui...
Dear All, I am opting for Cisco 4431 router on which we will be terminating 150 Mbps circuits, and IPSec tunnel will be configured to transport the traffic. IPSec throughput can reach upto 100 Mbps in this case do i require FL-44-HSEC-K9 license for...
Hey guys, I have a huge network infrastructure that has been setup a certain way for about 10 years with hundreds of private networks all using ospf 1 area 0 to communicate to each other. Very few static routes to a few networks not advertised by osp...
Hello community, I'm migrating from RV320 to RV340. In RV320 I have 4 subnets in the same VLAN (192.168.1.2 / 192.168.3.1 / 192.168.25.1 / 172.25.0.238) but in RV340 it does not allow me to create a subnet on the same VLAN. As the pictures show:
Hello Everyone, We migrated DHCP service from Windows to Cisco Device (works perfectly fine) but our PXE imaging is broken after migration. I was trying trial and error and found below based on our requirements. Requirements: All devices (Microsoft S...
I posted this on the Cisco learning forum on a tutorial I'm following but I'm adjusting it a little bit, I ran into a wall that I'm not sure how to resolve.The topology is the following way: DMVPN version 3Router 1(10.1.1.5) - Hub Location A - throug...
Hi All, I'm leaning with my new Cisco 2921 router and I have a Comcast cable modem that sets the IP via DHCP from the ISP. I have configured the router with what I thought would work, but I seem to be missing something. When I connect my pc via eth...
Hello Experts,I am looking for somehelp in configuring PBR in Nexus. The current setup in IOS is :interface Vlan10ip address 172.27.206.1 255.255.255.0ip address 172.27.208.1 255.255.254.0 secondaryip policy route-map Vlan_10_to_Corproute-map Vlan_10...
Hello, The provider delivers a speed 200 mbps, and the ISR 4331 delivers a maximum of 100 mbps. sh run: ! ! ! interface GigabitEthernet0/0/0 ip address 123.456.789.149 255.255.255.252 ip nat outside negotiation auto crypto map VPN ! interface Gig...
Hi all ,I have two private networks.Each network use eBGP to peer with ISP PE router.I got the below error.if i advertise my LAN network in bgp table , the LAN network can reach the each others.Branch1router bgp 65200bgp log-neighbor-changesnetwork ...
Hello all I need to change the router from c2800 router to isr4331. The c2800 router has the fair-queue 64 256 0 command.but I can not find the fair-queue command on isr4331.How can I use the fair-queue command in isr4331 interface? C2800 routerinter...
Sorry if this question is mundane, but I am confused over the 'subnet' and 'mask' information displayed in the routing table. For example [in image]: The EIGRP network has 2 subnets and 2 masks, but for each directly-connected network there are 2 su...
