Hi all,Based on the diagram below, I would like to achieve the following,- When SVR1 (VLAN10) need to communicate with SVR2 (VLAN20), it will have to go through S1 and ASA2- When SVR3 (VLAN10) need to communicate with SVR3 (VLAN20), it will have to g...
we have set up our queues to match our carriers, they have set the top to classes to 40% and 39%, does this really make much of a difference then. From what I understand, a ratio is calculated and each class gets to transmit according to that ratio,...
Hi all,While doing some simulation, I encountered some problems.L3 Switch (L3S1) is able to ping to the HSRP IP address and R2 G0/0/1 IP address. However, PC0 is unable to ping to the HSRP IP address and R2 G0/0/1 IP address.Did I missed out any conf...
I am creating a Network with 5 separate Vlans, connecting to a single router with different sub interfaces. I have set up the ip helper-address, and can get IP addresses from the DHCP server to the devices. I am struggling to get the devices to conne...
Hello, On our Nexus switches we have a BGP peering with an external company. I need to advertise our WAN subnet into their BGP and need some help. They want me to use IP Prefix lists for the below subnets that exist in our WAN. 172.30.0.0/24 (we h...
Hi all, I have recently purchased a CCNA lab for home study and I have noticed that every time I boot up the router, I get a Readonly ROMMON initialized. I have not noticed this message before, so not too sure if this is normal or weather I have mess...
HI All, For PIM sparse-mode environment, does (*,G) entries on the show ip mroute table (last hop router) , means multicast traffic from the RP is flowing down and I can join the group? Do I need the (S,G) group to be present in order for the host ...
Good afternoon, I have a IR829, and I have a slight concern for when 5G hits the UK. I currently use dual connectivity with two 4G sims. Will the IR829 require any software or hardware upgrades?
Hello, please can can someone advise me on the benefits of having a private network with a 4G provider over a public network? I understand for security reasons, but what else? Thanks in advance. matt
Hi All, Recently purchased an ASA 5508-X w/ FTD. I'm trying to configure a flat network for it, but it seems to not be able to route out. I created the route rule and set the gateway in the WEB GUI but it doesn't seem like it'll stick? Here's a clean...
Hello, I have a problem with Cisco ASR-920-24SZ-IM, when I plugged the power cord to the router, the console shows up in this mode, which has only a few commands. I tried to boot the system, but the result is as in the following picturesI have tried...
Hi,I have a basic set up that does not seem to be working as expected.this is all physical set up which consist of:Cisco Router - 1900Switch - 2960-X2 Win 10 MachinesSet up:Router 1 - Fast0/0 - Ip 192.168.1.4 / 24 VLAN 99 - DG Ip 192.168.1.4PC 1 - 19...
I'm trying to send syslog to a syslog-server through an L2L ipsec tunnel. The tunnel is up but the logging host does not work. I've done a tcpdump on the syslog-server and don't see any messages coming from the remote peer. The full configuration fo...
On the Nexus 9k, the only MTU's are 1500 or 9216. The 4500-X supports a range from 1500 to 9170. OSPF especially is very sensitive to MTU mismatches. Does this mean that you cannot use jumbo frames between a Nexus and 4500-X switch, especially if ...
I set my Linux server to ping the remote PC (over an IPSEC L2L tunnel) every 600 seconds overnight. When I return in the morning the ping is stalled and will not restart. There is no log entry for denial in the logs. Bouncing the remote INSIDE-IN ...
