Hi Team,
I have trying to setup Iscsi boot for our esxi servers.
Below are the steps I followed.
1. Created common/global vlans Vlan-nfs-20, mangement-10, vmotion-30, vmtraffic-40,
Created vlan 50 for iscsi in FI-A and Created Vlan 50 for iscsi F...
Hi,
I am new to the VPC and want to configure VPC between two Cisco Nexus 5548 and ASA 5585. Snapshot is attached for the reference.
I have Two 1 gig Link between Cisco Nexus 5548 switch so please guide me is it ok for VPC configuration or 10 Gig ...
Hi Team,
I am planiing for Iscsi SAN boot for ESXI hosts. I need below suggestions pleae.
1. Type of ports to be configure for ISCSI traffic?
2. VPC is recommended or PC is recommended from Nexus5K to Fabric 6100?
3. From which firmware Iscsi boot ...
Hi,
Please help me to validate the below design
From top to bottom
1 ) asa cluster
2)core
3 ) distribution
From distribution full layer 3 and In core there is vpc configured for asa cluste
Thanks
Hi everybody!
I am writing this post because I need help configuring private VLANs on this environment.
I have no problems configuring a primary private VLAN and 200 secondary or communities VLANs on Cisco Nexus 9000.
I have also configured these pr...
HI Team,
I need to upgrade the software for Nexus1110-S (virtual service appliance) as shown in the description, however I am confused as to what software as the product shows both Nexus 1100 Cloud service platform and Nexus1010 virtual service appl...
Hello
I have 2 nexus 5000 (5596) n5000-uk9.6.0.2.N2.4.bin, I know that to enable Jumbo frames I have to create a policy,
But I have the following questions can I force some of the interfaces to work with 1500 instead of 9162?
When I do the policy...
I have Linux server which is is having 4x1gig ports. I am using balance-alb as bonding technique.
We have 2 switches in access-layer which is having 10gig link to the core. Can i connect these 2x1gig link to each switches for redundancy and load bala...
I have a customer that would like to change the MTU size to the maximum on their Nexus 6004 switch. I've done it on 5K's and 7K's, but if I'm reading correctly, on a 6K it has to be done via service policy. Can someone comfirm this?
Hi
According to the release notes passive optic cables are not supported on the non-EDC ports. Any ideas on how to check what ports are actually supporting EDC?
Rgds & thanks
This is probably a dumb question, but can you use something like a qlogic 8152 CNA as just a regular 10gig network adapter and plug it into a 3750 or does it have to paired with a Nexus type device?
Hi,
1000v VMWare switch it's not showing all vlans on trunk ports:
switch# sh run int veth390interface Vethernet390 inherit port-profile 0000-Nexus_Interface-TRUNK description Virtual_Router01, Network Adapter 10, Other VLANs switchport mode tru...
Hi
I have the below plan for dc firewall ,
In asa side will be trunk and the nexus side it will be vpc(asa will be in a cluster)
What are the pros and cons ?
Since vpc does not block any link how the traffic wil flow ?.
From the DC lea...
Hi,
I have attached a topology diagram , Stp shows little different for a vlan ( vlan 15 , root shows Another switch ) .
Could someone help to understand why is that ?
All three interface vlan are sonfigured (hsrp with high priority on aggr...
Hi Guyz, I have nexus 5548UP with fixed module, i have configured them as1-12 ehternet ports, 13 - 32 san ports. we are adding N55-M16UP expansion module. can i now configure as below.1/1 - 1/12 - ethernet1/13 - 1/32 - SAN2/1 - 2/8 - Ethernet.2/9 -...
