Software-Defined Access (SD-Access)

Resolved! Media Converter use with SDA

Are any media converters compatible with SDA? I need to connect multiple devices at different locations and am looking for a solution that doesn't require me to buy multiple switches for one device. I need PoE to power the device and have fiber comin...

11 cmd outputs on DNAC for 100 switch seperate file for each switch

Hi engineers i want 11 cmd output for 100 switches i want separate file for each switch can anyone guide how can i do this

assign tags to port in DNAC 2.2.3

hi Gents anyone here to give a clue how do we make subject? according to amazing hint from Assurance deployment guide " Note For a link to be considered a WAN link, you must manually assign the system-generated WAN tag to the required port. See "Ass...

Resolved! SD Access Switch Upgrades

HiSo we are running FiAB with eWLC installed, I want to upgrade the IOS-XE image on our 9300/9500 Swithches, 1. IOS-XE and eWLC image versions must mach ?2.In DNAC Image repository I see the different image es but dont see any eWLC images downloaded...

SD-Access Using LISP Pub/SUB for DataCenter Failover

We are implementing a SD-Access greenfield using LISP Pub/Sub for SD-Access transit. We have two data centers each with an internet egress point through a firewall located at each site. Apart from a youtube video (which is good) I have not been abl...

Resolved! DNAC 2.3.7.6 new multicast features?

noticed DNAC preparing config like below which affecting some multicast applications in the overlay. cannot find it in any RNs. currently it looks like this only fixable via Day-N template with allowing affected subnets with ACE in ACL. Anybody can e...

Resolved! Issue Configuring L3 Handoff on second border node on same VLAN

Hello Everyone,We are building an SDA network with two separate border and control plane nodes ( collated both roles on same device) that are connected by BGP to a fusion firewall (Active/Standby). When DNAC configures the L3 border handoff, I provid...

Resolved! Cisco DNA License for C1121 Router

I would like to know if Cisco requires me to install a DNA license on the C1121 router, even though I do not plan to use DNA. I will only use CLI mode. I know that there are other platforms that require purchasing a DNA license even if you don't us...

Integrating CC 2.3.5.x with ISE 3.2+ and dynamic SGT assignment

So we currently run CC 2.3.5.6 with a fully integrated ISE 3.0 and we use policy set for Wired+Wireless Authentication and have 3 VNs in SDA with multiple hierarchical L2 VN/AnyCast Gateways and associated IP Pools in CC. Simply put: depending on MAC...

Border redundancy and iBGP

Hi,in this document , it says that in case of External+Internal border where BGP is imported into LISP and LISP is redistributed back into BGP, tags are needed to prevent iBGP to LISP route imports and hence avoid potential loops.Can someone, please,...

Resolved! Fusion Firewall with Intermediate L3 Hop

We are deploying the similar design as shown in the attached picture ( source: Cisco Live) where we have Nexus vPC switch as L3 hop between Border and Firewalls.BGP sessions will be established directly between:Border Nodes and NexusNexus & Firewalls...

Resolved! No Devices Found When Deploying VNs to Fabric Devices in Cisco DNAC

Trying to deploy VNs to the fabric devices, but when I reach the preview configuration step, it shows "no devices found." The VN has already been created and assigned under the fabric site.Some quick checkupFabric devices (Border Nodes, Control Plane...

SD-Access FIB loopback0 change IP

Hi, I have a working location with single 9300X working as FIB - i.e. it runs edge, contorl, border and also embedded WLC functionality. The fabric is working good. But now I need to change the Loopback0 IP address (due to global network renumbering)...

Cisco 3650CX SGT not working

Hi Cisco Community We have used some C3560CX as office extenders and now want to activate SGT. Unfortunately this does not work and we do not yet understand the reasons. A new C9200CX works perfectly. There are contradictory announcements and ma...

MACsec with SDA roadmap

Hi All, Hope you’re doing well! Just one small question – if MACsec support is on the roadmap for SD-Access? Or there are no plans to support it at all? Any input would be very welcome

Software-Defined Access (SD-Access)

Forum Posts

Resolved! Media Converter use with SDA

11 cmd outputs on DNAC for 100 switch seperate file for each switch

assign tags to port in DNAC 2.2.3

Resolved! SD Access Switch Upgrades

SD-Access Using LISP Pub/SUB for DataCenter Failover

Resolved! DNAC 2.3.7.6 new multicast features?

Resolved! Issue Configuring L3 Handoff on second border node on same VLAN

Resolved! Cisco DNA License for C1121 Router

Integrating CC 2.3.5.x with ISE 3.2+ and dynamic SGT assignment

Border redundancy and iBGP

Resolved! Fusion Firewall with Intermediate L3 Hop

Resolved! No Devices Found When Deploying VNs to Fabric Devices in Cisco DNAC

SD-Access FIB loopback0 change IP

Cisco 3650CX SGT not working

MACsec with SDA roadmap

One-way Audio & Intermittent Unregistration Post-Phone Replacement

Use ISE pxGrid to locate jabber clients using CER

SD-Access FIB loopback0 change IP

Cisco DNA Center - unable to remove edge node from fabric site

Network Templates filtering by Site shows irrelevant templates

Design SDAccess deploy, BN single switch with Nexus VPC as fusion

BGP routes filters in Catalyst Center automation

Trustsec Enforcement

PXE boot on SDA not working

In SD-Access, one VN can carry how many subnets?