Hello, We have installed two new switches (5&6) on an existing Fabric Stack Edge (4 switches), we can see all the S/N on the DNAC Inventory, but device-tracking configuration is not applied on all new ports/switches. SW-WTCP3-NT-S-1#show switch det...
-
-
-
-
This community is for technical, feature, configuration and deployment questions.
For production deployment issues, please contact the TAC! We will not comment or assist with your TAC case in these forums.
Please see How to Ask the Community
-
Forum Posts
Dears;We are on the verge of acquiring a SDA solution on this final stage we shall decide the amount of device that we should secure, saying this let me present my questions.1. Since C9120AXI-E and C9130AXE-E are similar products what is the advantag...
Resolved! LISP Route in "Route_rejected" status?
Hi,First time post. Apologies in advance if this a too in depth a question for here, but you don't know unless you try.The scenario is that we are on the journey of moving to SD-Access. We have a normal fabric with a standard VN setup, up and working...
Hello,I am having a complicated issue, I am doing some test with the TAC but its a bit more than that I believe. Here is my problem, when you connect the the network the first time it work fine. If you click disconnect and reconnect it says ''Cant co...
HiWe are full SD Access at work now and I was wondering could I manage a device via DNAC that isnt part of the Fabric on a site? So I want to install a 2 Switch stack in our DMZ I'm wondering if this is possible then maybe I could still use DNAC to k...
HiCan ayone explain and add link on how to set up DNAC/ISE Intergration and what technoligies are used,?? (is the intergration Cert based) ??.Thanks
Hello guys, In DNAC, the Authentication Template can be tuned to adjust the Authentication method order, the timers, etc. This template is represented as an IOS-XE template which itself calls a policy-map (ex: "PMAP_DefaultWiredDot1xClosedAuth_1X_MAB...
Hi, We are implementing our new SDA network We have an issue for the ip phones registration that it takes a very long time to register to CUCM [about 55 minutes] When it connected, it got ip address from infoblox, then it send request to CUCM untill ...
HiWe are proposing an SDA solution to a customer. They intend to retain a pair of 3rd party firewalls as their fusion device. The intention is to connect each Border to one of the firewalls. However, since the firewalls are in HA only one will be ...
Hey all!I'm having a bit of a brain lock to be honest and I'm surprised how there is no easy way to find documentation mentioning this ( or I'm just clueless) but, I'm having an issue with VN I created and mapped an SGT to, is not propagated to ISE.D...
Is the Meraki dashboard integration is possible with DNAC 2.3.3.7, can anybody please suggest here.As I checked the data sheet of 2.3.5 it is possible.https://www.cisco.com/c/en/us/products/collateral/cloud-systems-management/dna-center/nb-06-dna-cen...
Campus LAN (not too big) with a pair of CP/BN (for the entire campus) Several buildings with Dist switches (Intermediate nodes) and Fabric Edge (FE) nodes. LAN Automation will be building by building, or single building at a time in 2 passes - first ...
HelloI have now completed the SDA/DNA > Catalyst Center course and I am glad that I can now look a littledeeper into the subject.But I still have two burning questions that interest me and therefore I would like to take this opportunity hereyes, now ...
I followed the procedure specified in the guide and tried two different versions and I got the same error. https://www.cisco.com/c/en/us/td/docs/cloud-systems-management/network-automation-and-management/dna-center/2-3-5/install_guide/2ndgen/b_cisco_...
Hi everyone, we have issue with my SD-Access Environment. We build new Building and start to provision AP, but when we do provisioning to fabric face an issue. Issue says like this "Following AP(s) are assigned to Floor(s), which are not managed by t...
