We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
I've seen lots of posts from people having problems routing traffic between two vlans with some complicated examples. Can anyone post a simple step-by-step example for an SG300 switch (in layer 3 mode) to configure two vlans and sending traffic betw...
I have a SG200-26P. I have the most simple question imaginable, but it's not answered anywhere that I can find. Here goes:There are 24 "regular" ports on the switch.In addition to the 24 ports there is a second set of 4 ports to the right of the 24...
Hi. Sometimes I Wonder if Firmware are tested before public release. We have a stack of 4 brand new SG500X. I have the same problem on all Firmware I tested so far, including the latest (dated 2 feb): => There's no way to change Management IPV4 Addre...
Hi everyone, I hope you guys can help me with this one, Here is my current networkTo make that work I have created 2 static routes on my firewalls that point to my sw's vlan interfaces Gateway that way I can talk from 10 to 500 No I want to end those...
Hi all, I'm having an issue with getting wake on LAN working and am hoping someone can help me out. Our network is comprised of a number of Cisco SG500-52 switches on which we have configured port security to use MAC address bypass and RADIUS. The ma...
Hi again, I am slowly getting to the correct configuration thanks to a lot of assistance from this forum. I am at the point where the VLANs are created and I can access the internet from each device and I can ping devices on other VLANs. I can als...
Resolved! SG300-10 Console Settings??
Hello all,I am trying to connect to the console of this SG300-10 using a Cisco console cable, but am not getting anywhere with an actual connection. I am using Putty with the settings of 9600-8-n-1-None-None. I have also tried with baud rate of 19200...
Hello Community, this is my first post here and I hope to get an answer for a really weird behaviour. We have a SG350XG-24F switch and attached to it a few HP ProLiant Server. NICs on HP servers are also with SFP+ slots. NICs are connected to SG350XG...
Hello,as i connect the GBIC Modul to the Switch in the history of ROM it is identified.As i want to adjust the Port 18 it is shown as 1000 Mb (Kable) not as 10 Gb and not working.Firmware is 1.4.9.04Does somone have an solution?Thank you!
The release notes for 1.4.10.06 state that an upgrade to 1.3.5.x should be done first. However no such update exists. Current boot code is 1.0.0.12 and image is 1.0.8.3. It wants an .stk file but new format is .ros. Boot images for larger switche...
Resolved! SG 200-08p Wont upgrade firmware
I have a fleet of the SG-200-08P switches which are way behind on firmware. I went to upgrade them to the newest firmware available: "sx200_fw_1.3.7.18.ros"After about a 5-7 minute wait, the web interface returned the message (tired multiple time...
Resolved! Oversized Switch
Hi, I am replacing several components to my SOHO network and I have a switch question related to the size of the switches. I have Gb download speed from my ISP and I am trying to prevent a bottleneck or speed degradation to the max extent possible. ...
So quick question guys/ladies. Does the Meraki MS (switch) line support netflow. For example Meraki switch MS250 or MS225. I have been reading and reading documentation to find out but I do not see any settings where I can set up netflow on the ...
I want to update the firmware on a Cisco SG200 50 Port PoE smart switch. When I go to the Cisco product page:https://www.cisco.com/c/en/us/support/switches/sg200-50p-50-port-gigabit-poe-smart-switch/model.html#~tab-downloadsI see the latest update as...
Hi everyone,I'm certainly not an expert, I'd rather say a novice about the configuration of a switch.Our network has grown and today we find ourselves having to connect 2 locations via a radio link.What I'm trying to do is use 2 radio links to double...
