Switches - Small Business

Cisco really needs to do something about this since if you create a static bind using a MAC address the device generally doesn't receive the assigned IP but if you enter the client ID instead it will.  I don't know if the switch just doesn't check th...

my Cisco Small Business 300 Series Managed Switch is having problem its power light is static and not blinking after i have reset it, it started blinking but after vlan configuration and creation of trunk i plugged into the trunk and back it...

Hello I have an Cisco SG-200-50 Switch and i have a problem with the LACP configuration. Actually I have an HP ProCurve 1800-24G Switch and here I configure LACP. On my PC (Windows 10) I have already activatet Teaming / LACP. All works fine. Th...

Hi,I just can't get the dynamic vlans working. I've tried everything, switch in L3 mode, switch in L2, several port configs, several tunnel configs in Radius server (freeradius 2.1.1)Here's the final switch config:config-file-headerswitchf460dcv1.3.7...

Hello, I have a Meraki router with a SG300 switch and 2 x WAP561 Access points on ports 47/48.  We currently have VLAN 1 (192.168.10.0/24) setup as our main network.  I have setup another VLAN for our guest network on our Meraki router, VLAN 50 (192...

i connect SG550XG to SG500X by sfp supported module for 10G. but it is not connecting. Is there any special command for using fiber connectivity? OM4 Multi-mode 50/125µm, Duplex, LC  SFP-10G-SR SG550XG >> interface  te1/0/9  ip address 192.168.3.1 ...

Dear all,  I have a problem with our network, we have several cisco small business switches (300SG & 200SG), we configured the last 4 ports from any switch to be Trunk ports and the rest are Access ports.The default VLAN on the switches is VLAN 17. ...

Hi all,can somebody please advise how to configure the SG500 to be invisible to traceroutes?I do have InterVLAN routing enabled on this device and don´t want the device to be visible in traceroutes from one vlan into another.I´ve played around with A...

i have Cisco SF300-24 24-Port 10/100 Managed Switch with Gigabit Uplinks (SRW224G4-K9-NA) and three others, i can use that switch as core switch and other as access, kindly advise

Operating a SG300-10 on my home office network. I originally experienced issues backing up the startup and/or running config. Specifically, attempts to backup caused the switch to reboot. This occurs whether the attempt is made through the web interf...

Hi there,I need your help to get InterVLAN Routing working on a SG500-28 Stack with 2 Units.I think I am missing something with how the port type needs to be set ( trunk or access ) and how the VLAN tagging ( tagged / untagged ) has to be on specific...

Hi  I am trying to configure snmp for PRTG to monitor the usage of all the ports.using the command  "snmp-server community public ro" but I am unable to get the data in PRTG. I am using "SG300-28 28-Port Gigabit Managed Switch" and "SW version    1.3...

I have two SG300 switches with same vLANs on each.  When I TRUNK between any port 1-48 the vLANs inter-connect fine.  When I attempt on TRUNK between port 49-51 (LINK/ACT) ports, vLAN 1 still works, but all other vLANs do not work.  What am I missing...

Hi, I'm unable to access Windows shared directory via Anyconnect . It says "You do not have permission to access  this directory", but I have full access to that directory locally. I've used same credential as I used to access it locally. And also I...