Switch: Cisco C9200L-48P-4XIOS XE Version: 17.12.03 (cat9k_lite_iosxe)IP Phones: ShoreTel 115 and Yealink T30PAccess Points: UniFi AC ProAll switch ports are functioning for data transmission, but none are supplying power to PoE devices. I have alrea...
Hi, we’re experiencing an issue where freshly installed Windows 11 PCs are being disconnected from the network exactly 7 days after installation. The devices are connected to a Catalyst 3650 switch (we’ve also seen this behavior on a 9200 series) run...
Hi, I'm a bit confused with the private vlan commands. Maybe you can help me. I need to connect to add a server via trunk, that should contain "normal" vlans and a community vlan. This is my config: interface Gi1/0/1switchport mode private-vlan trunk...
Hi guys,I have this output from a cable diagnostic test that I did. How do I pinpoint at which end the pair is open? Is it at the closet end or user end?show cable-diagnostics tdr int f0/39TDR test last run on: January 27 10:45:54 Interface Speed Loc...
So I might have found a bug with the c1300 4.1.0.76 firmware, but I wanted to get yalls opinion before I report a bug.Heres the issue:I am sending syslogs to rsyslog so that they can be ingested into grafana loki via promtail, but the messages are ge...
Dear SirsI would like to switch off and back on again the POE function on one channel of my Cisco 2960 Catalyst switch.I have a number of Latte Panda PCs attached and sometimes one may need to be powered down and powered up again without switching th...
The Cisco Nexus 9000 Series NX-OS Interfaces Configuration Guide, Release 10.5(x) tells at chapter Load Balancing Using Port Channels:"Configuring hash load balancing applies to unicast and multicast traffic on Cisco Nexus 9200, 9300-EX, and 9300-GX ...
Hello to everyone does anyone knows about eve.ng that how can i export the lab with configuration ?i searched about eve in community but i didnt find my answer
We have a dedicated call center in our hospital. We are using a IP PBX software from a outsourced vendor. The software is installed in our PCs to attend the enquiry calls.The client pcs using in call center is a data vlan in one of the access switch....
Hi, The switch 2960 has space 20,922,880b. the new ios size is 17,769KB, after transferring, switch would have about 3.6MB left, it should work, but the left space would be a little bit small. how do you think about it? 2#dirDirectory of flash:/2 -rw...
Hi, we have upgraded ios in c9200 stack without issue when verifying md5 after copying image. but recently after copying image to c9300, all of them cannot show correct verifying number, Is this something wrong? Thanks
Hey All, Wanted to see if anyone could help me. I was given a pair of Cisco Nexus 3172PQ switches for my lab. The only issue is I am not familiar with NXOS. I have some experience with IOS but none with NXOS so I am having a hard time with the config...
I'm working through a lab and I'm assuming i missing something obvious. I can ping switch0 from Router 1 but not server0. Same with R2 I can ping switch1 but neither hosts.Any help appreciated I'm just banging my head against a wall
I have been bashing my head trying to figure out what might have broke or why its not working, but let me explain the set up process.We have 3 Panels for industrial machinery that daisy chain to a control panel that acts as a hub or unmanaged switch....
I'm thinking that I have a corrupt IOS. But if I can't copy an new IOS from USB to flash, I probably will not have any better luck with hyperterm. Is the switch just worthless?? switch:switch: dir flash:Directory of flash:/2 -rwx 2002 <date> config...
