Hello All, I have a situation where I could use some help.My infrastructure is configured as followed:A cisco router where dot1.q is used to create vlans. A stack of 2960S switches where all the vlans have been configured.I need to connect some devic...
Forum Posts
Looks like they came out this month - curious if anyone has any initial feedback on them.https://www.cisco.com/c/en/us/products/switches/business-350-series-managed-switches/models-comparison.htmlI have a handful of SG350Xs (which I believe are consi...
Hello, I would like to check if it's possible to use NCS1K-2KW-AC-CBL power cord for Cisco Catalyst 9600 Series 2000W AC Power Supply to utilize 208V input voltage. The power cord is not listed on the main webpage for North America cords but it looks...
Resolved! use CAT6a cable on 2960X switch?
hi guys,i would like to know whether the cat6a cable is compatible with catalyst 2960X switch or not?(there are CAT6a cables already existing in my environment and dont wanna waste them)the CAT6a cable should be able to comply with old categories suc...
i, i´m getting some error in my network catalyst 6800 and 6500 core switches. i would like to know what´s does it mean ? %EARL-SW2_DFC3-1-EXCESSIVE_PARITY_ERROR: EARL 0: Parity error detected in VRAM %SYS-DFC4-2-CFORKMEM: Process creation of NTI Trig...
Hi all,we got this message:%FWM-1-MET_INDEX_RESOURCE_EXHAUSTION: Met index exhausted we upgraded to 7.3 and were told by Cisco that this will increase the MET; how can we check the current MET size?
We have some 2960-X with management interfaces have been connecting to separate network. Is there a way to use a default gateway or some static routes for these interfaces? 3850 for example have separate mgmt-vrf.
I have a cisco 3750X switch and i upgraded it to the latest IOS : 15.2(4)E10)I set up the switch IP address and now am presented with the WebUI below:Cisco 3750X WebUI How would I go about creating and managing VLANs in the WebUI? Did I install the w...
I have had the switch for a year now with no issues. But, I wanted to access the IOS via CLI. I'm discovering that this may not be an option. My current firmware version is 2.4.5.71. I checked the Cisco support page and I couldn't find a newer, o...
Resolved! When to enable Portfast?
Switch to switch?Switch to server?Switch to desktop?Switch to router?Switch to firewall?By the way, I've decided to disable auto-negotiation and set speeds for 100/full or 1000/full for ports and connecting hosts.
Hello, Where can i find latest firmware for Cisco SG350-28P ? Thanks
We have new cisco 881 ruther withCisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.0(1)M4, RELEASE SOFTWARE (fc1), in this software we have problem with integration with old routers which are on IOS 12.4. So we are wondering is i...
Hello I have a Cisco 9300 switch connected to an AT&T Router and able to ping outside (www) from the switch but not able to ping or gain access from any VLAN.Any Help or Advise would be appreciated. I am trying to eliminate the need of a Cisco Router...
I am trying to setup an Isolated Private VLAN and running into some issue mixing the enterprise & SMB environments. I have a few switch ports I want to configure to talk to the internet only and not allow the devices connected to these ports to talk ...
Resolved! VS-S720-10G
Dearsi have VS-S720-10G and i am looking for 16 port 10G module , do anybody can suggest me a module becz the module i found it is end of sale and the new module is compatible with sup2t, anybody can help me this info how i can install a compatible 1...
