Hi All My Switch 3650 show: Core 0: CPU utilization for five seconds: 98%; one minute: 99%; five minutes: 99% How can I solving?
Hi All My Switch 3650 show: Core 0: CPU utilization for five seconds: 98%; one minute: 99%; five minutes: 99% How can I solving?
Hi, im looking for switch cisco SG250X-48, but i want to know if this switch allows 10g with sfp+, because in the datasheet, i only can find that this switch allow 1000 Mbps. So please can you help me with this answer and what sfp+ is compatible wi...
Hello all,New to this board. Working towards getting my CCENT1 and I have access to two Cat 2960's. I blew out the Flash and uploaded the IOS 12.2(55) to give these layer 2 switches layer 3 routing. I enabled 'sdm prefer' and 'ip routing' but the swt...
Dear ,I'm trying to create GRE tunnel between two Cisco 877 routers by using ddns interface Tunnel1 ip address 10.10.10.1 255.255.255.252 tunnel source Dialer1 tunnel destination hat45.dnsalias.netThe domain name under hat45.dnsalias.net is resolvin...
Hey everyone, I hope someone can give me some advice on this as I'm going around in circles at the moment. I can see why it is happening, but can't get to a resolution as yet. Anyway: At our company we have a switch stack comprised of four 3650 swi...
Hi dear, I try to configure Cisco StackWise Virtual in switch 9407r but StackWise command are not support. Below you find show version command output : Switch#sh versionCisco IOS XE Software, Version 16.09.02Cisco IOS Software [Fuji], Catalyst L3...
Using 3636C as L3 core switch and I see a lots of InDiscards (around 0.15% on all interface) . The data rate of the interfaces is not high, like 1Gbps on 10G and 40G links. Here is one interface : RX 234305677 unicast packets 15428 multicast pa...
Have this settings:"monitor session 3 source interface Te1/1/3monitor session 3 destination interface Po1"show interface te1/1/3get:"TenGigabitEthernet1/1/3 is down, line protocol is down (notconnect)"On the Po1 i get information from Gi 1/0/3
When we create 2 Route-map with two sequence number i.e. 10 & 20then which route-map will be read first by Router
I have been observing this error extensively on my standalone switch. Feb 8 07:13:51.708: %PLATFORM_STACKPOWER-4-CABLE_B_CURRENT_OUT: Switch 1 stack power cable 2 outward current is over the limitFeb 8 07:14:51.829: %PLATFORM_STACKPOWER-4-CABLE_B_CUR...
hello sir,I am working in the area of Software Defined Networks.can we configure openflow in Cisco Catalyst WS-C2960X-24PD-L and connect with Opendaylight Controller.
Hello, I have problem with my WS-C4500X-32. After update ROMMON to firmwareupgradeallK10-150_1r_SG15.SPA my module is Fail. Supervisor don't see any Gbic inserted inplug in interfaces (No XCVR). Some one have any ideas to fix it ? Switch#sh moduleC...
my LAN traffic will come to a firewall , there i have a PBR for http traffic to forward to N5K . n5k acting as a ITD , redirect requests to proxy , and traffic to internet will go with proxy IP. do i need to use VIP under ITD Service , is it requi...
We have a cisco 3560x-24-p with a C3KX-NM-10G module, we are trying to connect the Cisco switch to a Mellanox SX1012 switch using a Mellanoxx MC2309130-002-V-A2 cable however the switch doesn't recognise the sfp+ on the cable. We have updated to 15.0...
We have two Nexus 5548s running version 7.1(4)N1(1). They are configured with VPC. We want to upgrade firmware from current version to 7.3(3)N1(1). Since it's running VPC, is there anything special I need to do regarding the firmware upgrade, such...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-23-2025 01:45 PM | ||
07-08-2025 11:44 PM | ||
07-04-2025 02:13 AM | ||
06-26-2025 10:05 AM | ||
06-16-2025 07:47 PM |
User | Count |
---|---|
13 | |
11 | |
9 | |
5 | |
4 |