Resolved! SNMP MIBs and Traps on C2960
Any default enabled SNMP traps on C2960? User has to configure every single event, including port/link UP/Down, packet loss, overload status for an SNMP server to automatically be notified these trap events?
Forum Posts
Resolved! Catalyst 3560CX web interface problem
Hello, I'm having issues with the web interface on a 3560CX. I've updated the IOS to version 15.2(5)E2 and since then the web interface has been playing up (see attachment). I've created a user with privilege 15 and a secret pass. I've done the ip ...
Dear All, Does anyone know if nx-os supports multiple conditional advertise map statements? advertise-map RM-ADVERTISE-OFFICE1 exist-map RM-EXIST-LOOP-OFFICE1 advertise-map RM-ADVERTISE-OFFICE2 exist-map RM-EXIST-LOOP-OFFICE2 I have successfully us...
I have problem while connecting Cambium Networks ePMP1000 Connectorized Radio AP with Cisco Catalyst Switch 3750/2960. Before I connect Cambium Networks ePMP1000 Connectorized Radio AP into my corporate network in this case to Cisco Catalyst Switch 3...
Trying to configure ikev1 IPSec tunnel from Azure CSR 1000v back to my data center to use GRE over IPSec. It's driving me crazy, because the tunnel is not coming up. VPN config in our private datacenter is the same as other tunnels we have, but I see...
I just red the below question and its answer. Please explain some one about that. also explain what is 0.0.0.0 and 255.255.255.255 which single network command will start ospf on all interfaces of a router ? answer : netwrok 0.0.0.0 255.255.2...
Resolved! turning off debugging
Hello, is it necessary to turn off all debugging when finished with a remote session to a Cisco swtich/router to prevent load on the CPU i.e will this debugging CPU load continue even after you have exited the remote session ?
Hello,Installed the CNA and connected to C2960X-24PS-L, however it reported device not supported.What is missing? The version of the IOS is 15.2(2)E7, is this the right version for CNA to be supported?K
Hi, i'm sorry if the question a little bit confusing. So i'm currently learning about trunk troubleshoot (ccna). In the book (ccna 200-125 official cert guide) said that both ends have to have same allowed trunk configuration. But when i tried in...
Dear Support all, I would just like to know if there is any specification document or comments. The test is below, Firstly I have checked the IEEE802.1X auth user then disable Windows7 NIC setting but Interface L1 connect keeps up. After that the C8...
forget username and password to enter the Setup in modem DPC2425 how to restore to return to factory values?
I have two cisco switches 4500 and connected as VSSi upgraded the firmware now but they stuck in the rommon mode after each restart please see the some of the conf file: DHAAKSW01-MDF#sh bootflash:-#- --length-- ---------date/time--------- path 1 ...
Hay everyone I am new to experimenting with vlans and could do with some some advice. The design I have is three floors of a building, with each floor containing hosts from three different vlans (hr,finance,production) Currently I have a layer...
We have 2 Cisco 1921, as R1 and R2 connected to 2 Cisco2960G SW1 and SW2 Cisco 2960G are connected to each other using a Trunk interface. Main point to point link is connected to SW1 and redundant hand off of same point to point link is connected to ...
Resolved! Can't ping vPC'd Nexus 3Ks
Hello and thanks for any help with this! I have 2 Nexus 3Ks (N3K01/N3K02) that I have just figured out how to vPC together (vPC keepalive using 2x10gb per switch LACP port-channeled/vPC peer link using 2x40gb per switch LACP port-channeled). All ty...
